Click here

UPPER INSTRUMENT PANEL REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    TABLE OF BOLT, SCREW AND NUT

    A01IOHFE01
    Tip:

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

  2. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  4. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH


    1. Detach the 8 claws and 2 clips, and remove the front door scuff plate.

  5. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  6. Click here

    REMOVE COWL SIDE TRIM BOARD LH


    1. Detach the 2 clips and guide, and remove the cowl side trim board.

  7. Click here

    REMOVE COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure described for the LH side.

  8. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip.

  9. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  10. Click here

    REMOVE FRONT PILLAR GARNISH LH


    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tip:

      Allow the front pillar garnish to hang by the front pillar garnish clip.

      Table 1. Text in Illustration
      *1 Front Pillar Garnish Clip
    2. A01ISK0E01

      Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish.

      Note:

      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tip:

      Tape the tips of the needle-nose pliers before use.

      Table 2. Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

    3. Detach the 2 claws and remove the front pillar garnish.

    4. A01IR1KE01

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note:

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

        Table 3. Text in Illustration
        *1 Curtain Shield Airbag Assembly
        *2 Adhesive Tape
        *3 Protective Cover
  11. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  12. Click here

    REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY


    1. Remove the 2 screws <B>.

    2. Detach the 7 claws and 5 guides.

    3. Disconnect the connector and remove the glove compartment door.

  13. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. for Automatic Air Conditioning System:


      1. A01IQDGE01

        Put protective tape around the instrument panel finish panel end LH.

        Table 4. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover A, detach the 3 clips and 2 guides, and remove the instrument panel finish panel end LH.

    2. for Manual Air Conditioning System:


      1. A01ITLUE01

        Put protective tape around the instrument panel finish panel end LH.

        Table 5. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover A, detach the 3 clips and guide, and remove the instrument panel finish panel end LH.

  14. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END RH


    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end RH.

        Table 6. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover A, detach the 3 clips, claw and 2 guides, and remove the instrument panel finish panel end RH.

    2. A01IQX3E01

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end RH.

        Table 7. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover A, detach the 3 clips, claw and guide, and remove the instrument panel finish panel end.

  15. Click here

    REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Detach the 8 claws and 4 guides.

    2. Disconnect the connector and remove the center instrument panel register.

  16. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Detach the 4 claws and 11 guides, and remove the instrument cluster finish panel.

  17. Click here

    REMOVE COMBINATION METER ASSEMBLY


    1. A01INRI

      Remove the 2 screws.

    2. Detach the clip.

    3. A01INN0

      Detach the clamp.

    4. Disconnect the connector and remove the combination meter.

  18. Click here

    REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Audio, for Radio and Display Type)


    1. Detach the 4 clips, 3 claws and 3 guides, and remove the center instrument cluster finish panel.

  19. Click here

    REMOVE STEREO OPENING COVER WITH BRACKET (w/o Audio)


    1. Remove the 4 bolts and stereo opening cover.

  20. Click here

    REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)


    1. A01IOAB

      Remove the 4 screws.

    2. A01IP7W

      Pull the radio receiver assembly with bracket to detach the 4 clips on the backside of the radio receiver assembly with bracket.

    3. Disconnect the connectors and remove the radio receiver assembly with bracket.

  21. Click here

    REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


    1. A01IRU5

      Remove the 4 screws.

    2. A01IU6S

      Pull the radio receiver and display receiver assembly with bracket to detach the 4 clips on the backside of the radio and display receiver assembly with bracket.

    3. Disconnect the connectors and remove the radio and display receiver assembly with bracket.

  22. Click here

    REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01ISYGE01

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  23. Click here

    REMOVE POSITION INDICATOR HOUSING ASSEMBLY (except Manual Transaxle)


    1. Detach the 5 claws and 3 clips.

    2. Disconnect the connector and remove the position indicator housing.

  24. Click here

    REMOVE SHIFTING HOLE COVER (for Manual Transaxle)


    1. Twist the T washer in the direction indicated by the arrow and remove it.

      Table 8. Text in Illustration
      *1 T Washer

    2. Remove the knob spring.

    3. Detach the 5 claws and 3 clips, and remove the shifting hole cover.

  25. Click here

    REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (except Manual Transaxle)


    1. for Automatic Air Conditioning System:


      1. Remove the 3 screws <C>.

      2. Detach the 2 claws, 4 clips and 5 guides, and remove the lower center instrument panel finish panel.

        Tip:

        If the 2 claws shown in the illustration are difficult to detach, detach the 4 clips of the air conditioning control and remove the lower center instrument panel finish panel together with the air conditioning control.

    2. A01IOIV

      for Manual Air Conditioning System:


      1. Remove the 3 screws <C>.

      2. Detach the 4 clips, 2 claws and 5 guides, and remove the lower center instrument panel finish panel.

  26. Click here

    REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)


    1. for Automatic Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 2 claws, 4 clips and 5 guides, and remove the lower center instrument panel finish panel.

        Tip:

        If the 2 claws shown in the illustration are difficult to detach, detach the 4 clips of the air conditioning control and remove the lower center instrument panel finish panel together with the air conditioning control.

    2. A01IN3V

      for Manual Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 4 clips, 2 claws and 5 guides, and remove the lower center instrument panel finish panel.

  27. Click here

    REMOVE NO. 2 SWITCH HOLE BASE


    1. for LHD:

      Detach the 5 claws and 5 clips, and remove the No. 2 switch hole base.

    2. A01IQ8G

      for RHD:

      Detach the 3 claws and 5 clips, and remove the No. 2 switch hole base.

  28. Click here

    REMOVE NO. 1 SWITCH HOLE BASE


    1. w/ Entry and Start System:


      1. Detach the 2 claws and 2 clips.

      2. Disconnect the connector and remove the No. 1 switch hole base.

    2. A01ISBI

      w/o Entry and Start System:


      1. Detach the 2 claws and 2 clips, and remove the No. 1 switch hole base.

  29. Click here

    REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for 4 Speakers:


      1. Detach the claws and clips shown in the illustration on the bottom of the panel. Then, using the 2 claws on the side of the panel towards the front of the vehicle as pivot points, lift up the panel in the direction indicated by the arrow in the illustration to remove the No. 1 instrument panel speaker panel.

    2. A01IUSL

      for 6 Speakers:


      1. Detach the claws and clips shown in the illustration on the bottom of the panel. Then, using the 2 claws on the side of the panel towards the front of the vehicle as pivot points, lift up the panel in the direction indicated by the arrow in the illustration until the speaker connector can be disconnected.

      2. A01IREG

        Disconnect the connector and remove the No. 1 instrument panel speaker panel together with the speaker.

  30. Click here

    REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Tip:

    Use the same procedure described for the No. 1 instrument panel speaker panel.

  31. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Remove the passenger airbag bolt <A>.

    2. A01IOAC

      Disconnect the connector and clamps.

    3. Remove the 3 screws <B>.

    4. A01ISGS

      Pull up the instrument panel safety pad to detach the 2 clips, 4 claws and 5 guides, and remove the instrument panel safety pad.

      Note:

      Be careful not to damage the steering wheel.