HEATER FUEL PUMP (w/ Combustion Type Power Heater) INSTALLATION


  1. INSTALL HEATER PUMP ASSEMBLY


    1. Install the heater pump assembly with the nut.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
    2. Connect the 2 fuel hoses as shown in the illustration.

    3. Using pliers, grip the claws of the clips and slide the 2 clips.

    4. Connect the connector.

      A01IP1DE01
      Text in Illustration
      *1 Paint Mark *2 0 to -3 mm (0 to -1.18 in.)
  2. INSTALL COWL TOP OUTER PANEL


    1. Install the cowl top panel with the 9 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
  3. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for DPF)


    1. A01INRQE02

      Connect the 2 vacuum hoses.

      Note

      Connect the vacuum hoses so that the painted marks of the 2 vacuum hoses are as shown in the illustration.

    2. A01IT6Y

      Install the sensor with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. Connect the sensor connector and attach the wire harness clamp.

  4. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A01ISAD

      Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body and install the wiper motor and link.

    2. A01ITHG

      Install the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A01IQJZ

      Connect the connector and attach the clamp to install the wire harness to the cowl top panel.

  5. INSTALL COWL TOP VENTILATOR LOUVER LH


    1. A01IPRQ

      Attach the 6 claws and 5 guides to install the cowl top ventilator louver LH.

    2. Install the clip.

    3. A01INVH

      Attach the 2 claws and 2 guides to install the center cowl top ventilator louver.

  6. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01IQI1

      Attach the 4 claws and 5 guides to install the cowl top ventilator louver RH.

    2. Install the clip.

  7. INSTALL HOOD TO COWL TOP SEAL


    1. A01IQHZ

      Attach the 7 clips and 2 claws to install the hood to cowl top seal.

  8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01
      Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

      Clean the wiper arm serrations.

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITAIE01
      Text in Illustration
      *1 Mark for Blade Position

      Position the blade tip within the range shown in the illustration.

      Tech Tips

      The lower limit of the range is indicated by the mark on the glass.

    5. Install the front wiper arm and blade assembly LH with the nut.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand when tightening the nut.

    6. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01
      Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

      Clean the wiper arm serrations.

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITNDE01
      Text in Illustration
      *1 Mark for Blade Position

      Position the blade tip within the range shown in the illustration.

      Tech Tips

      The lower limit of the range is indicated by the mark on the glass.

    5. Install the front wiper arm and blade assembly RH with the nut.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand when tightening the nut.

  10. INSTALL FRONT WIPER ARM HEAD CAP


    1. A01ISR6

      Install the front wiper arm head cap.

      Tech Tips

      Use the same procedure for all front wiper arm head caps.

  11. INSTALL NO. 1 ENGINE COVER


    1. A01INMI

      Attach the 4 clips to install the No. 1 engine cover.