CAN COMMUNICATION SYSTEM Short to B+ in CAN Bus Line

DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

  • Short between CAN bus lines and +B

  • ECM

  • Brake actuator assembly (skid control ECU)

  • Certification ECU (smart key ECU assembly)*1

  • Air conditioning amplifier assembly

  • Spiral with sensor cable sub-assembly (steering angle sensor)

  • Yaw rate sensor

  • Main body ECU (instrument panel junction block assembly)

  • Center airbag sensor assembly

  • Power management control ECU*1

  • Power steering ECU assembly

  • Radio and display receiver assembly*2

  • Combination meter assembly

  • Engine stop and start ECU*3

  • No. 1 junction connector

  • No. 2 junction connector

WIRING DIAGRAM

A01IU9BE01
A01IRHWE01
A01IO0NE01
A01IO9ZE01
A01INW3E01

INSPECTION PROCEDURE

Note

For vehicles with an entry and start system:

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)


    1. A01IS0GE02
      Text in Illustration
      *a Front view of DLC3

      Disconnect the H88 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H16-6 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H16-14 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  4. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    1. A01IS0GE02
      Text in Illustration
      *a Front view of DLC3

      Disconnect the A50 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H16-6 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H16-14 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY)


    1. A01IPK4E01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A50-8 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A50-19 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A01IPK4E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A50-7 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A50-18 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A01IPK4E03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A50-10 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A50-21 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 1 JUNCTION CONNECTOR

  9. CONNECT CONNECTOR


    1. Reconnect the A50 No. 1 junction connector.


    NEXT

  10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY)


    1. Disconnect the brake actuator assembly (skid control ECU) connector.

      A01IOBVE01
      Text in Illustration
      *A for CVT *B for Manual Transaxle
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      		 *b Front view of DLC3

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for CVT
      Tester Connection Switch Condition Specified Condition
      A78-26 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A78-14 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      for Manual Transaxle
      Tester Connection Switch Condition Specified Condition
      A79-2 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A79-16 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR ASSEMBLY (CANH, CANL)

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

  11. CONNECT CONNECTOR


    1. Reconnect the A50 No. 1 junction connector.


    NEXT

  12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)


    1. A01IQ1HE11
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Main Body ECU [Instrument Panel Junction Block Assembly])
      *b Front view of DLC3

      Disconnect the main body ECU (instrument panel junction block assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H81-15 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H81-16 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  13. CONNECT CONNECTOR


    1. Reconnect the A50 No. 1 junction connector.


    NEXT

  14. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)


    1. A01IP16E01
      Text in Illustration
      *A for 1ZR-FAE, 2ZR-FAE
      *B for 1WW
      *a

      Front view of wire harness connector

      (to ECM)
      *b Front view of DLC3

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 1ZR-FAE, 2ZR-FAE
      Tester Connection Switch Condition Specified Condition
      A76-13 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A76-26 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      for 1WW
      Tester Connection Switch Condition Specified Condition
      A76-26 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      A76-25 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

      Tech Tips

      *: Replacement procedure:

      for 1ZR-FAE Click here

      for 2ZR-FAE Click here

      for 1WW Click here


    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

    OK

    REPLACE ECM*

  15. CONNECT CONNECTOR


    1. Reconnect the A50 No. 1 junction connector.


    NEXT

  16. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A01ISBKE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 junction connector)
      *b Front view of DLC3

      Disconnect the No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-10 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-21 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

    OK

  17. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

    Note

    For vehicles without an entry and start system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier Assembly)".


    1. A01ISBKE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-1 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-12 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  18. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CERTIFICATION ECU)


    1. A01ISBKE03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-2 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-13 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  19. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

    Note

    For vehicles with a 1WW engine type and entry and start system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Power Steering ECU Assembly)".


    1. A01ISBKE21
      Text in Illustration
      *A w/o Entry and Start System
      *B for 1ZR-FAE, 2ZR-FAE (w/ Entry and Start System)
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Entry and Start System
      Tester Connection Switch Condition Specified Condition
      H88-2 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-13 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      for 1ZR-FAE, 2ZR-FAE (w/ Entry and Start System)
      Tester Connection Switch Condition Specified Condition
      H88-8 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-19 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  20. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    1. A01ISBKE04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-3 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-14 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  21. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

    Note

    For vehicles without a radio and display type, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Spiral with Sensor Cable Sub-assembly)".


    1. A01ISBKE05
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-4 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-15 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  22. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    1. A01ISBKE06
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-5 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-16 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  23. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)


    1. A01ISBKE07
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-6 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-17 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  24. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

    Note

    For vehicles without a stop and start system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Center Airbag Sensor Assembly)".


    1. A01ISBKE08
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-8 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-19 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  25. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    1. A01ISBKE09
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-11 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-22 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  26. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01ISBKE10
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H88-9 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H88-20 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

  27. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  28. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    1. A01IOV2E32
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)
      *b Front view of DLC3

      Disconnect the power management control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H71-14 (CA1H) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H71-13 (CA1L) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    C

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)

    A

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  29. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  30. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU)


    1. A01IMYPE15
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Certification ECU [Smart Key ECU Assembly])
      *b Front view of DLC3

      Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H51-9 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H51-10 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  31. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  32. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

    A01IQRWE01
    Text in Illustration
    *A for Automatic Air Conditioning System *B for Manual Air Conditioning System or w/ o Air Conditioning System
    *a

    Front view of wire harness connector

    (to Air Conditioning Amplifier Assembly)

    		 *b Front view of DLC3

    1. Disconnect the air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Automatic Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      H46-11 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H46-12 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      for Manual Air Conditioning System or w/o Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      H118-8 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H118-9 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  33. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  34. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)


    1. A01IQI0E03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Power Steering ECU Assembly)
      *b Front view of DLC3

      Disconnect the power steering ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H49-2 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H49-8 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

    OK

    REPLACE POWER STEERING ECU ASSEMBLY Click here

  35. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  36. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)


    1. A01IUJME30
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)
      *b Front view of DLC3

      Disconnect the radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H105-9 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H105-10 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

  37. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  38. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    1. A01INDJE10
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)
      *b Front view of DLC3

      Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H128-4 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H128-3 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

    OK

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

  39. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  40. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR)


    1. A01ISN8E05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Yaw Rate Sensor)
      *b Front view of DLC3

      Disconnect the yaw rate sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H68-2 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H68-3 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)

    OK

    REPLACE YAW RATE SENSOR Click here

  41. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  42. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU)


    1. A01IO5EE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Engine Stop and Start ECU)
      *b Front view of DLC3

      Disconnect the engine stop and start ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H121-15 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H121- 16 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ENGINE STOP AND START ECU (CANH, CANL)

    OK

    REPLACE ENGINE STOP AND START ECU Click here

  43. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  44. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    1. A01IQQME21
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *b Front view of DLC3

      Disconnect the center airbag sensor assembly connector Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H19-13 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H19-22 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

  45. CONNECT CONNECTOR


    1. Reconnect the H88 No. 2 junction connector.


    NEXT

  46. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    1. A01INRHE07
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)
      *b Front view of DLC3

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H62-22 (CANH) - H16-16 (BAT) Ignition switch off 6 kΩ or higher
      H62-23 (CANL) - H16-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here