TRANSMISSION CONTROL CABLE REMOVAL


  1. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Remove the front exhaust pipe assembly Click here.

  2. REMOVE BATTERY SERVICE HOLE COVER


    1. A01IPWV

      Remove the clip and battery service hole cover.

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  6. REMOVE NO. 2 CYLINDER HEAD COVER


    1. A01IRS7

      Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

      Note

      Attempting to detach both front and rear clips at the same time may cause the cover to break.

  7. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01IU5G

      Remove the 5 clips.

    2. Detach the 4 hooks and remove the radiator support opening cover.

  8. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A01IQN6E01

      Disconnect the cable from the positive (+) battery terminal.

    2. Remove the bolt and loosen the nut.

    3. Remove the battery clamp.

  9. REMOVE BATTERY

  10. REMOVE BATTERY TRAY

  11. REMOVE BATTERY CARRIER


    1. A01INC1

      Disconnect the 2 wire harness clamps from the battery carrier.

    2. Remove the 2 bolts and disconnect the radiator pipe from the battery carrier.

    3. A01IN2I

      Remove the 4 bolts and battery carrier.

  12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01ISEG

      Disconnect the mass air flow meter connector.

    2. Detach the 2 clamps and disconnect the wire harness.

    3. A01IP4V

      Disconnect the 2 clamps.

    4. A01IPUC

      Disconnect the PCV hose.

    5. Loosen the band and remove the air cleaner cap.

  13. REMOVE AIR CLEANER CASE


    1. A01IQF0

      Detach the wire harness clamp from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  14. REMOVE BOX PANEL SUB-ASSEMBLY


    1. Remove the box panel sub-assembly Click here.

  15. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

    A01IRZYE01
    Text in Illustration
    *1 Protective Tape

    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQ6AE01
      Text in Illustration
      *1 Protective Tape

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips and guide, and remove the instrument panel finish panel end.

  16. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    A01IU46E01
    Text in Illustration
    *1 Protective Tape

    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips, claw and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQX3E01
      Text in Illustration
      *1 Protective Tape

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips, claw and guide, and remove the instrument panel finish panel end.

  17. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

    A01IQZA

    1. Detach the 8 claws and 4 guides.

    2. Disconnect the connector and remove the center instrument panel register.

  18. REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)


    1. for Radio Receiver Type:

      Remove the radio receiver assembly Click here.

    2. for Radio and Display Type:

      Remove the radio receiver assembly Click here.

  19. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Audio)

    A01IRZ3

    1. Detach the 4 clips, 3 claws and 3 guides, and remove the center instrument cluster finish panel.

  20. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Audio)

    A01ISEY

    1. Remove the 4 bolts and stereo opening cover.

  21. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. Twist the shift lever knob in the direction indicated by the arrow and remove it.

      A01ISYGE01

  22. REMOVE SHIFTING HOLE COVER

    A01IOOWE01
    Text in Illustration
    *1 T Washer

    1. Twist the T washer in the direction indicated by the arrow and remove it.

    2. Remove the knob spring.

    3. Detach the 5 claws and 3 clips, and remove the shifting hole cover.

  23. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    A01IOJM

    1. for Automatic Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 2 claws, 4 clips and 5 guides, and remove the lower center instrument panel finish panel.

        Tech Tips

        If the 2 claws shown in the illustration are difficult to detach, detach the 4 clips of the air conditioning control and remove the lower center instrument panel finish panel together with the air conditioning control.

    2. A01IN3V

      for Manual Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 4 clips, 2 claws and 5 guides, and remove the lower center instrument panel finish panel.

  24. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 1 console box insert.

      A01IUSGE01

  25. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 2 console box insert.

      A01IQC5E01

  26. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01IPGW

    1. Remove the screw <D>.

    2. Disconnect the connector.

    3. Detach the 4 clips and remove the lower No. 1 instrument panel finish panel.

  27. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    A01IT4Y

    1. Remove the 3 nuts and front No. 1 floor heat insulator.

  28. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01IPQME02
      Text in Illustration
      *1 Select Cable
      *2 Shift Cable

      Disconnect the control shift cable from the shift lever assembly.

    2. Pinch the areas indicated by the arrows and disconnect the control select cable.

    3. A01IUJQ

      Detach the 2 claws and disconnect the control cable assembly.

    4. A01IOZW

      Remove the 2 clips and disconnect the 2 cables from the transaxle.

    5. A01IRNL

      Remove the 2 clips and disconnect the 2 cables from the control cable bracket.

    6. A01IOFU

      Remove the bolt and detach the bracket of the control cable assembly.

    7. A01IQR5

      Remove the 2 nuts and detach the grommet of the control cable assembly.