TRANSMISSION CONTROL CABLE

Click here
INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
1. Attach the grommet of the control cable assembly with the 2 nuts.
  
  5.0 N*m 51 kgf*cm 44 in.*lbf
2. Attach the bracket of the control cable assembly with the bolt.
  
  5.0 N*m 51 kgf*cm 44 in.*lbf
3. Connect the 2 cables to the control cable bracket with 2 new clips.
4. Connect the 2 cables to the transaxle and install the 2 clips.
5. Engage the 2 claws, and install the control cable assembly to the shift lever assembly.
  
  Note:
  Make sure that the claws are firmly engaged.
6. Install the control shift cable to the shift lever assembly.
  
  Table 1. Text in Illustration
  
  *1 Select Cable
7. Release the lock of the cable length adjustment structure of the select cable.
  1. Turn the stopper.
  2. Pull the lock piece outward from the case to release the lock.
  3. Return the stopper.
8. While pressing the shift and select lever shaft (*1) and pin (*2), push in the pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.315 in.) below the N position).
9. Connect the control select cable to the shift lever assembly.
10. Push the slider against the inhibitor wall.
  Note:
  - Do not pull up the slider.
  - When adjusting the cable, make sure that the shift lever is not in the 1 or 2.
11. Lock the cable length adjustment structure of the select cable.
  1. Turn the stopper.*1
  2. Push the lock piece into the case.*2
  3. Return the stopper to prevent the lock from being released.*3
    Note:
    - Push the lock piece as far as it will go.
    - Confirm whether the cable length adjustment structure is locked securely.
12. Release the pin that fixes the transmission outer lever.
  1. Pull the pin toward the left front side of the vehicle.
Click here
INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
1. Install the front No. 1 floor heat insulator with the 3 nuts.
  
  5.5 N*m 56 kgf*cm 49 in.*lbf
Click here
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

(Click here)
Click here
INSTALL AIR CLEANER CASE
1. Install the air cleaner case with the 3 bolts.
  
  7.0 N*m 71 kgf*cm 62 in.*lbf
Click here
INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
INSTALL AIR CLEANER CAP SUB-ASSEMBLY
1. Connect the air cleaner hose assembly to the turbocharger, and slide the clamp secure it.
  
  Table 2. Text in Illustration
  
  *a Upper
  
  Tip:
  The direction of the hose clamp is indicated in the illustration.
2. Attach the 4 clamps to install the air cleaner cap sub-assembly.
3. Connect the PCV hose to the cylinder head cover sub-assembly, and slide the clamp secure it.
4. Attach the clamp and connect the mass air flow meter connector.
Click here
INSTALL BATTERY CARRIER
1. Install the battery carrier with the 4 bolts.
  
  19 N*m 189 kgf*cm 14 ft.*lbf
2. Attach the 2 clamps to connect the wire harness.
Click here
INSTALL BATTERY TRAY
Click here
INSTALL BATTERY
Click here
INSTALL BATTERY INSULATOR

Table 1. Text in Illustration
*1	Select Cable

Table 2. Text in Illustration
*a	Upper

INSTALL BATTERY CLAMP SUB-ASSEMBLY

Attach the hook of the battery clamp sub-assembly to the battery carrier.
Partially tighten the nut and temporarily install the bolt.
Adjust the battery clamp sub-assembly position.

Tighten the nut and bolt.

for bolt
17 N*m	168 kgf*cm	12 ft.*lbf
for nut
3.5 N*m	36 kgf*cm	31 in.*lbf

Click here
INSTALL NO. 1 ENGINE COVER
1. Attach the 4 clips to install the No. 1 engine cover.
Click here
CONNECT CABLE TO POSITIVE BATTERY TERMINAL
Click here
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Click here
INSTALL FRONT EXHAUST PIPE ASSEMBLY
1. Install the front exhaust pipe assembly (Click here).

TRANSMISSION CONTROL CABLE INSTALLATION