Click here

ELECTRONICALLY CONTROLLED BRAKE SYSTEM VSC OFF Indicator Light Remains ON

Click here
Click here Click here
DTC Code DTC Name
  VSC OFF Indicator Light Remains ON
Click here

DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If VSC control is turned off, the VSC OFF indicator light will come on.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication system DTC is output (Click here).

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

  2. Click here

    CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED


    1. Check if the skid control ECU connector is securely connected.

      OK
      The connector is securely connected.

  3. Click here

    CHECK AUXILIARY BATTERY


    1. Check the auxiliary battery voltage.

      Standard Voltage
      11 to 14 V

  4. Click here

    READ VALUE USING INTELLIGENT TESTER (VSC OFF SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Select the Data List on the intelligent tester (Click here).

      Table 1. ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      TRC(TRAC)/VSC OFF SW VSC OFF switch / ON or OFF

      ON: Switch on

      OFF: Switch off

      		 -
      TRC/VSC Off Mode VSC OFF switch / Normal, TRC OFF, Unknown or VSC OFF

      Normal: Normal mode

      TRC OFF: TRC off mode

      Unknown: Unspecified

      VSC OFF: VSC off mode

      		 -

    4. Using the intelligent tester, check the switch input and mode condition on the intelligent tester changes according to VSC OFF switch operation.

      Result
      Result Proceed to
      OK A
      NG (Switch input and mode condition display do not change.) B
      NG (Switch input is normal, but mode condition display does not change.) C

  5. Click here

    INSPECT COMBINATION METER ASSEMBLY


    1. Turn the power switch off.

    2. Perform the Active Test of the combination meter (meter CPU) using the intelligent tester (Click here).

    3. Check the combination meter.

      OK
      The VSC OFF indicator light turns on or off in accordance with the intelligent tester operation.
      Tip:

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).


  6. Click here

    INSPECT VSC OFF SWITCH


    1. A01NIDJE05

      Turn the power switch off.

    2. Disconnect the VSC OFF switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      6 (+) - 7 (E) Switch is pushed in Below 1 Ω
      6 (+) - 7 (E) Switch is not pushed in 10 kΩ or higher

  7. Click here

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    1. A01NJRME02

      Disconnect the skid control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A90-19 (CSW) - F33-6 (+) Always Below 1 Ω
      A90-19 (CSW) - Body ground Always 10 kΩ or higher
      F33-7 (E) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *1

      Front view of wire harness connector

      (to Skid Control ECU)
      *2

      Front view of wire harness connector

      (to VSC OFF Switch)
      Tip:

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).


  8. Click here

    REPLACE SKID CONTROL ECUClick here

  9. Click here

    INSPECT CAN COMMUNICATION SYSTEMClick here

  10. Click here

    CONNECT CONNECTOR TO ECU CORRECTLY

  11. Click here

    CHARGE OR REPLACE AUXILIARY BATTERY

  12. Click here

    REPLACE COMBINATION METER ASSEMBLYClick here

  13. Click here

    REPLACE VSC OFF SWITCHClick here

  14. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR