Click here

REAR CENTER SEAT OUTER BELT ASSEMBLY INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. A019OJV

      Install the rear center seat outer belt assembly with the bolt and nut.

      Bolt
      7.5 N*m 77 kgf*cm 66 in.*lbf
      Nut
      42 N*m 428 kgf*cm 31 ft.*lbf
  2. Click here

    INSTALL REAR SEAT SHOULDER BELT COVER


    1. A019OH1

      Engage the claw and guide, and install the rear seat shoulder belt cover as shown in the illustration.

    2. A019MSF

      Engage the 3 claws to install the belt support plate.

  3. Click here

    INSTALL REAR SEATBACK COVER WITH PAD


    1. A019KA1E01

      Temporarily install the side airbag so that it is stored inside the rear seatback cover with pad.

      Table 1. Text in Illustration
      *1 Side Airbag
    2. A019MD7E01

      Install bracket A onto the bolt and insert the guide.

      Table 2. Text in Illustration
      *1 Bracket A *2 Bracket B

    3. Install bracket B onto the bolt and insert the guide.

    4. Install the rear seatback cover bracket with the nut.

      5.6 N*m 57 kgf*cm 50 in.*lbf
      Note:

      • For vehicles with side airbags, the side airbags may not be activated normally unless the rear seatback cover is securely installed.

      • Check that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    5. A019NSU

      Using hog ring pliers, install a new hog ring.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog ring, take care to minimize wrinkles as much as possible.

    6. Engage the hook.

    7. A019OX9

      Install the rear seat belt hook with the bolt.

      6.0 N*m 61 kgf*cm 53 in.*lbf
    8. A019L6O

      Using hog ring pliers, install 6 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    9. Engage the 5 hooks.

    10. A019KHRE01

      Engage the 2 fasteners and install the rear seatback cover with pad.

      Table 3. Text in Illustration
      *1 Fastener
  4. Click here

    INSTALL REAR SEAT HEADREST SUPPORT LH


    1. A019MOR

      Engage the 2 claws to install the rear seat headrest support LH.

  5. Click here

    INSTALL REAR SEAT HEADREST SUPPORT RH


    1. A019NV5

      Engage the 2 claws to install the rear seat headrest support RH.

  6. Click here

    CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. A019NOF

      Connect the rear center seat outer belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
  7. Click here

    INSTALL REAR SEAT SHOULDER BELT HOLE COVER


    1. A019OP9

      Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 guides.

    2. Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 claws and install the cover.

  8. Click here

    INSTALL SEAT BELT ANCHOR COVER CAP


    1. A019JV4

      Engage the 2 claws and install the seat belt anchor cover cap.

  9. Click here

    INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY


    1. A019NOT

      Engage the guide.

    2. Install the No. 1 fold seat stopper band assembly with the bolt.

      9.0 N*m 92 kgf*cm 80 in.*lbf
  10. Click here

    INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH


    1. A019NBV

      Engage the guide.

    2. Engage the 2 clips and install the rear seatback board carpet assembly RH.

  11. Click here

    INSTALL REAR SEATBACK COVER RH


    1. A019OYE

      Engage the 4 claws to install the rear seatback cover RH.

  12. Click here

    INSTALL TONNEAU COVER HOOK HOLDER


    1. A019OPL

      Engage the 2 guides.

    2. Install the 2 tonneau cover hook holders with the 2 screws.

  13. Click here

    INSTALL REAR SEAT LOCK STRIKER


    1. A019LQ2

      Using a T45 "TORX" socket, install the "TORX" bolt to the rear seat lock striker.

      21 N*m 214 kgf*cm 16 ft.*lbf
  14. Click here

    INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR


    1. A019LYM

      Install the rear seatback lock striker protector.

  15. Click here

    INSTALL REAR SEAT CUSHION COVER WITH PAD


    1. A019P2Z

      Using hog ring pliers, install 2 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019JWQ

      Using hog ring pliers, install 2 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    3. A019M7W

      Engage the 2 elastic bands.

    4. A019OQH

      Engage each hook.

    5. A019NR2

      Engage the 2 hooks to install the rear seat cushion cover with pad.

  16. Click here

    INSTALL REAR SEAT CUSHION MOULDING RH


    1. A019JVX

      Engage the 2 guides as shown in the illustration.

    2. Install the rear seat cushion moulding RH with the 2 screws.

  17. Click here

    INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH


    1. A019ODZ

      Install the No. 1 reclining adjuster release handle RH with the 3 screws.

  18. Click here

    INSTALL REAR SEAT COVER CAP


    1. A019JNQ

      Engage the 3 claws to install the rear seat cover cap.

  19. Click here

    INSTALL REAR CENTER SEAT ASSEMBLY


    1. A019P2B

      Engage the elastic band.

    2. A019OO4

      Install the rear seat center seat assembly with the 4 bolts.

      21 N*m 214 kgf*cm 16 ft.*lbf
  20. Click here

    INSTALL UPPER CENTER SEAT HINGE COVER LH


    1. A019O0G

      Install the upper center seat hinge cover LH.

  21. Click here

    INSTALL REAR SEAT INNER BELT ASSEMBLY


    1. Install the rear seat inner belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
  22. Click here

    INSTALL REAR SEAT ASSEMBLY RH


    1. Install the rear seat assembly RH (Click here).