CAN COMMUNICATION SYSTEM (for RHD) Short in CAN Bus Lines

DESCRIPTION

There may be a short circuit between the V Bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.

  • Short between CAN bus lines

  • ECM

  • Parking brake ECU assembly

  • Main body ECU (multiplex network body ECU)

  • Spiral with sensor cable sub-assembly (steering angle sensor)

  • Yaw rate sensor

  • Combination meter assembly

  • Skid control ECU assembly

  • Power steering ECU assembly

  • Air conditioning amplifier assembly

  • Network gateway ECU

  • Front steering control ECU*

  • Center airbag sensor assembly

  • Multi-media module receiver assembly

  • Certification ECU (smart key ECU assembly)

  • Power management control ECU

  • No. 1 CAN junction connector

  • No. 2 CAN junction connector

  • No. 3 CAN junction connector

WIRING DIAGRAM

A01FVJ3E02
A01FUJQE02
A01FR1ZE02

INSPECTION PROCEDURE

Note


  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output Click here.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed Click here.

Tech Tips


  • Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

  • Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

PROCEDURE


  1. CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      A01FRZ9E31
      Text in Illustration
      *1 No. 3 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 3 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N116 G W DLC3

    2. Disconnect the DLC3 branch line connector from the No. 3 CAN junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

    OK

  2. CHECK FOR SHORT IN CAN BUS LINES


    1. Reconnect the DLC3 branch line connector to the No. 3 CAN junction connector.

    2. A01FSTYE01
      Text in Illustration
      *a Front view of DLC3

      Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

    3. While observing the resistance value shown on the tester, disconnect connectors N107, N108, N109, N110, N111, N112, N113, N114, N115, N116, N117, N118, N119, N120, N121, N122, U48, U49, U50 and U51 from the No. 1 CAN junction connector, No. 2 CAN junction connector or No. 3 CAN junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

      Tech Tips

      Disconnect the branch line connectors other than those of the DLC3.

      A01FTT1E01
      Text in Illustration
      *1 No. 1 CAN Junction Connector *2 No. 2 CAN Junction Connector
      *3 No. 3 CAN Junction Connector *4 ECM
      *5 Parking Brake ECU Assembly *6 Front Steering Control ECU (w/ Variable Gear Ratio Steering System)
      *7 Certification ECU (Smart Key ECU Assembly) *8 Network Gateway ECU
      *9 Yaw Rate Sensor *10 Center Airbag Sensor Assembly
      *11 Main Body ECU (Multiplex Network Body ECU) *12 Power Steering ECU Assembly
      *13 Skid Control ECU Assembly *14 DLC3
      *15 Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) *16 Air Conditioning Amplifier Assembly
      *17 Combination Meter Assembly *18 Multi-media Module Receiver Assembly
      *19 Power Management Control ECU - -
      A01FTEJE04
      Text in Illustration
      *1 No. 1 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 1 CAN Junction Connector)

      		 - -
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      U48 B W Parking Brake ECU Assembly
      U49 R W Front Steering Control ECU*
      U50 P W No. 2 CAN Junction Connector
      U51 G W ECM

      • *: w/ Variable Gear Ratio Steering System

      A01FUGME08
      Text in Illustration
      *1 No. 2 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 2 CAN Junction Connector)

      		 - -
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N107 B W No. 3 CAN Junction Connector
      N108 R W Certification ECU (Smart Key ECU Assembly)
      N109 G W Network Gateway ECU
      N110 B W Yaw Rate Sensor
      N111 Y W Center Airbag Sensor Assembly
      N112 V W Main Body ECU (Multiplex Network Body ECU)
      N113 P W No. 1 CAN Junction Connector
      N114 L W Power Steering ECU Assembly
      A01FUGME09
      Text in Illustration
      *1 No. 3 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 3 CAN Junction Connector)

      		 - -
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N115 L W Skid Control ECU Assembly
      N116 G W DLC3
      N117 R W Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
      N118 Y W Air Conditioning Amplifier Assembly
      N119 V W Combination Meter Assembly
      N120 P W Power Management Control ECU
      N121 B W No. 2 CAN Junction Connector
      N122 B W Multi-media Module Receiver Assembly

      Note

      Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus lines.

      Result
      Result Proceed to
      The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of the branch lines.) A
      The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B

    4. When there is a short in one or more of the branch lines:


      1. Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

        Tech Tips


        • Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

        • Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


    B

    CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR) Click here

    A

  3. CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE)


    1. Disconnect the ECM main bus line connector from the No. 1 CAN junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

      A01FVTFE05
      Text in Illustration
      *1 No. 1 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 1 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      U51 G W ECM

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      Result
      Result Proceed to
      The resistance is still below 54 Ω when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) A
      The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) B

    B

    CHECK FOR SHORT IN CAN BUS LINES (ECM) Click here

    A

  4. CHECK FOR SHORT IN CAN BUS LINES (POWER MANAGEMENT CONTROL ECU MAIN BUS LINE)


    1. Disconnect the power management control ECU main bus line connector from the No. 3 CAN junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

      A01FRZ9E32
      Text in Illustration
      *1 No. 3 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 3 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N120 P W Power Management Control ECU

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the ECM main bus line connector disconnected.

      Result
      Result Proceed to
      The resistance is still below 1 MΩ when the power management control ECU connector is disconnected. (There are no shorts in the power management control ECU or between its main bus lines.) A
      The resistance becomes 1 MΩ or more when the power management control ECU connector is disconnected. (There is a short in the power management control ECU or between its main bus lines.) B

    B

    CHECK FOR SHORT IN CAN BUS LINES (POWER MANAGEMENT CONTROL ECU) Click here

    A

  5. CHECK NO. 1 CAN JUNCTION CONNECTOR


    1. Disconnect the CAN main bus line connector from the No. 1 CAN junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

      A01FVTFE07
      Text in Illustration
      *1 No. 1 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 1 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      U50 P W No. 2 CAN Junction Connector

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the power management control ECU main bus line connector disconnected.


    NG

    CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) Click here

    OK

    REPLACE NO. 1 CAN JUNCTION CONNECTOR

  6. CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)


    1. Reconnect the CAN main bus line connector from the No. 1 CAN junction connector.

      A01FRZ9E25
      Text in Illustration
      *1 No. 2 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 2 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N113 P W No. 1 CAN Junction Connector

    2. Disconnect the CAN main bus line connector from the No. 2 CAN junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the power management control ECU main bus line connector disconnected.


    NG

    CHECK NO. 2 CAN JUNCTION CONNECTOR Click here

    OK

    REPAIR OR REPLACE CAN BUS MAIN LINES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

  7. CHECK NO. 2 CAN JUNCTION CONNECTOR


    1. Disconnect the CAN main bus line connector from the No. 2 CAN junction connector.

      A01FRZ9E33
      Text in Illustration
      *1 No. 2 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 2 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N107 B W No. 3 CAN Junction Connector

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the power management control ECU main bus line connector disconnected.


    NG

    CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR) Click here

    OK

    REPLACE NO. 2 CAN JUNCTION CONNECTOR

  8. CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)


    1. Reconnect the CAN main bus line connector from the No. 2 CAN junction connectors.

      A01FRZ9E27
      Text in Illustration
      *1 No. 3 CAN Junction Connector - -
      *a

      Rear view of wire harness connector

      (to No. 3 CAN Junction Connector)

      		 *b Front view of DLC3
      Wiring Color
      Code Color (CANH Side) Color (CANL Side) Connect to
      N121 B W No. 2 CAN Junction Connector

    2. Disconnect the CAN main bus line connector from the No. 3 CAN junction connectors.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the power management control ECU main bus line connector disconnected.


    NG

    REPLACE NO. 3 CAN JUNCTION CONNECTOR

    OK

    REPAIR OR REPLACE CAN BUS MAIN LINES (NO. 3 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  9. CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)


    1. A01FSTYE01
      Text in Illustration
      *a Front view of DLC3

      Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

    2. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected Click here.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Tech Tips

      If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).


    NG

    REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR

    OK

    REPLACE CORRESPONDING ECU OR SENSOR

  10. CHECK FOR SHORT IN CAN BUS LINES (ECM)


    1. A01FSTYE01
      Text in Illustration
      *a Front view of DLC3

      Reconnect the ECM main bus line connector to the No. 1 CAN junction connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Tech Tips

      If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.


    NG

    REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN BUS LINES)

    OK

    REPLACE ECM Click here

  11. CHECK FOR SHORT IN CAN BUS LINES (POWER MANAGEMENT CONTROL ECU)


    1. A01FSTYE01
      Text in Illustration
      *a Front view of DLC3

      Reconnect the power management control ECU main bus line connector to the No. 3 CAN junction connector.

    2. Disconnect the power management control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Connection Specified Condition
      N20-6 (CANH) - N20-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

      Tech Tips


      • Measure the resistance with the ECM main bus line connector disconnected.

      • If the resistance changes to 1 MΩ or more when the connector is disconnected, there may be a short in the ECM.


    NG

    REPAIR OR REPLACE CAN BUS MAIN LINES (POWER MANAGEMENT CONTROL ECU MAIN BUS LINES)

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here