POWER MANAGEMENT CONTROL ECU REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  3. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH


    1. Remove the luggage compartment trim cover LH.

  4. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. REMOVE INSTRUMENT SIDE PANEL RH

    A01FQQME01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel RH.

    2. Using a moulding remover, detach the 7 clips and remove the instrument side panel RH.

    3. w/ Airbag Cut Off Switch:


      1. Disconnect the connector.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    A01FS1UE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument panel finish panel end RH.

    2. Detach the 5 clips and 2 guides and remove the instrument panel finish panel end RH.

  9. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL

    A01FSJSE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the center instrument cluster finish panel.

    2. Detach the 9 clips and guide.

    3. Disconnect the connector and remove the center instrument cluster finish panel.

  10. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A01FT2W

    1. Detach the 5 clips and 2 guides.

    2. Disconnect the connectors, detach the clamp and remove the No. 2 instrument panel under cover sub-assembly.

  11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

    A01FVEAE01
    Text in Illustration
    *1 Screw <A>
    *2 Bolt <E>

    1. Remove the 3 screws <A> and 2 bolts <E>.

    2. Detach the 6 clips.

    3. Disconnect the connectors, detach the clamp and remove the glove compartment door assembly.

  12. REMOVE COWL SIDE JUNCTION BLOCK RH (for LHD)


    1. A01FUN9

      w/ VGRS System:


      1. Disconnect the 5 connectors.

      2. Using a clip remover, detach the 2 clamps.

    2. A01FU0U

      w/o VGRS System:


      1. Disconnect the connector.

      2. Using a clip remover, detach the clamp.

    3. A01FR2S

      Disconnect the 4 connectors.

    4. A01FT42

      Remove the bolt and nut.

    5. Remove the cowl side junction block RH from the reinforcement.

    6. A01FTL1

      Disconnect the 2 connectors and remove the cowl side junction block RH.

  13. REMOVE COWL SIDE JUNCTION BLOCK LH (for RHD)


    1. A01FRCG

      w/ VGRS:


      1. Detach the 5 connectors.

      2. Using a clip remover, detach the 2 clamps.

    2. A01FVM5

      w/o VGRS:


      1. Detach the connector.

      2. Using a clip remover, detach the clamp.

    3. A01FR6Z

      Disconnect the 7 connectors.

    4. A01FQPP

      Remove the bolt and nut, and remove the cowl side junction block LH.

    5. A01FV6E

      Disconnect the 2 connectors and remove the cowl side junction block LH.

  14. REMOVE ECU INTEGRATION BOX RH (for LHD)


    1. A01FUSU

      Disconnect all the connectors.

    2. A01FUZQ

      Remove the 2 nuts, bolt and ECU integration box RH.

  15. REMOVE ECU INTEGRATION BOX LH


    1. A01FTT9

      Disconnect all the connectors.

    2. A01FVW2

      Remove the 2 nuts, bolt and ECU integration box LH.

  16. REMOVE POWER MANAGEMENT CONTROL ECU


    1. A01FSDY

      for LHD:


      1. Detach 2 claws and remove the power management control ECU.

    2. A01FV1Q

      for RHD:


      1. Detach 2 claws and remove the power management control ECU.