LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Luxury Seat Type) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. Slide the lumbar support adjuster assembly LH downward to attach the 2 hooks and install it.

    2. Install the 2 bolts.

    3. Attach the 2 clips and install the 2 springs.

    4. Attach the 2 cable clamps.

    5. Connect the 2 connectors.

  2. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH


    1. Attach the hook to install the seatback climate control blower LH together with the rear air duct LH.

    2. Install the 2 screws.

    3. Attach the 2 claws to connect the rear air duct LH to the lumbar support adjuster assembly LH.

    4. Connect the connector.

  3. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. A01FRH7E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.

    3. Attach the wire harness clamp.

    4. Attach the 4 claws to install the 2 front seat headrest supports.

    5. Attach the wire harness clamp.

    6. Attach the hooks

    7. Connect the connector.

  4. INSTALL FRONT POWER SEAT SWITCH ASSEMBLY RH (w/ Shoulder Switch)


    1. Connect the connector.

    2. A01FSBZ

      Attach the 2 claws to install the front power seat switch assembly RH.

    3. Attach the wire harness clamp.

  5. INSTALL FRONT SEATBACK BOARD

    A01FVI7

    1. Slide the front seatback board upward to attach the 2 hooks and install it.

    2. Install the 2 screws.

  6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01FU56

    1. Slide the front seatback board sub-assembly LH upward to attach the 2 hooks and install it.

    2. Attach the 2 claws.

    3. Open the lower part of the front seatback board sub-assembly LH and install the 2 screws.

    4. Install the clip.

    5. Attach the hook to connect the rubber band.

    6. Connect the rubber band with the clip.

  7. INSTALL FRONT SEAT ASSEMBLY

    Click here

  8. CHECK SRS WARNING LIGHT

    Click here

  9. INSPECT SEAT BELT WARNING SYSTEM

    Click here

  10. PERFORM INITIALIZATION

    Note

    Under any of the following conditions, perform initialization of the position control ECU assembly.

    for LHD: Click here

    for RHD: Click here


    • The position control ECU assembly is replaced.

    • The power seat motor assembly is inspected or replaced.

    • The front seat adjuster is inspected or replaced.

    • The lumbar support adjuster assembly is inspected or replaced.

    • The front seatback adjuster assembly is inspected or replaced.

    • The front seatback support is inspected or replaced.

  11. INSPECT POWER SEAT CONTROL SYSTEM

    for LHD: Click here

    for RHD: Click here

  12. INSPECT SEAT HEATER SYSTEM

    Click here

  13. INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here

  14. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.