HYBRID BATTERY SYSTEM, Diagnostic DTC:P0A85-123

DTC Code DTC Name
P0A85-123 Hybrid Battery Pack Cooling Fan 1 Control Circuit High

DESCRIPTION

Refer to the circuit description for DTC P0A84-123 Click here.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A85 123 When the speed calculated based on the battery cooling blower assembly (for upper side) frequency (FP0) is out of the target control speed range (1 trip detection)

  • Battery cooling blower assembly (for upper side)

  • Battery smart unit

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 Click here.

INSPECTION PROCEDURE

CAUTION:


  • Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  • When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK FOR DTCS (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read output DTCs.

      Result
      Result Proceed to
      P0AFC-123 is not output. A
      P0AFC-123 is also output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (P0AFC-123) Click here

    A

  2. CHECK BATTERY SMART UNIT (FREQUENCY)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the front luggage compartment trim cover Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

    6. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

      Note

      If the Active Test cannot be performed, skip it and proceed to the next step to check Frequency. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

    7. Enter the following menus: All Data / Cooling Fan Frequency 1.

    8. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    9. A01FTKLE01
      Text in Illustration
      *a

      Component with harness connected

      (Battery Cooling Blower Assembly [for Upper Side])
      *b

      Rear view of wire harness connector

      (to Battery Cooling Blower Assembly [for Upper Side])

      While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

      Standard
      Tester Connection Condition Specified Condition
      X4-2 (FP0) - X4-4 (GND0) Battery cooling blower is operating Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less.

      Note

      Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Tech Tips

      Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Install the front luggage compartment trim cover.


    NG

    REPLACE BATTERY SMART UNIT Click here

    OK

    REPLACE BATTERY COOLING BLOWER ASSEMBLY (for Upper Side) Click here