SUB RADIATOR REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  3. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH


    1. Remove the luggage compartment trim cover LH.

  4. DISCONNECT CABLE FROM AUXILIARY NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE ENGINE ROOM SIDE COVER


    1. A01FTR0

      Remove the 4 clips and engine room side cover.

  6. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01FS00

      Remove the 7 clips and cool air intake duct seal.

  7. REMOVE NO. 1 AIR CLEANER INLET


    1. A01FUV7

      Remove the bolt and No. 1 air cleaner inlet.

  8. REMOVE ENGINE UNDER COVER


    1. A01FS2S

      Remove the 13 screws, 3 clips and engine under cover.

  9. DRAIN COOLANT (for Inverter)

    Note


    • Do not reuse the drained coolant because it may contain foreign objects.

    • Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.


    1. Remove the reservoir tank cap.

    2. A01FR2J

      Loosen the drain cock plug.

      CAUTION:

      To avoid the danger of being burned, do not remove the reservoir tank cap while the coolant for the inverter is still hot.

  10. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  11. REMOVE HOOD LOCK RELEASE LEVER PROTECTOR


    1. Disconnect the connector and detach the 2 clamps.

    2. A01FRM4

      Remove the 2 clips and hood lock release lever protector.

  12. REMOVE HOOD LOCK ASSEMBLY (for LHD)


    1. A01FU6G

      Remove the 3 bolts.

    2. A01FVLT

      Remove the hood lock from the hood lock control cable.

  13. REMOVE HOOD LOCK ASSEMBLY (for RHD)


    1. A01FVXG

      Remove the 3 bolts.

    2. A01FSV7

      Remove the hood lock from the hood lock control cable.

  14. DISCONNECT NO. 2 ENGINE ROOM WIRE


    1. A01FTN7

      Disconnect the cooling fan ECU connector.

    2. Detach the 6 wire harness clamps to disconnect the No. 2 engine room wire.

  15. DISCONNECT HOOD LOCK CONTROL CABLE COVER (w/ Cover)


    1. A01FR5P

      Detach the claw and remove the 2 screws to disconnect the hood lock control cable cover.

  16. REMOVE UPPER RADIATOR SUPPORT


    1. A01FQPC

      Disconnect the 3 connectors.

    2. Detach the 5 wire harness clamps to disconnect the wire harness from the upper radiator support.

    3. A01FVDX

      Remove the 5 bolts and upper radiator support.

  17. REMOVE HOOD LOCK CONTROL CABLE COVER (w/ Cover)


    1. A01FR19

      Remove the screw.

    2. Detach the claw and remove the No. 2 hood lock control cable cover.

  18. REMOVE RADIATOR ASSEMBLY


    1. A01FUKN

      Slide the clamp and disconnect the 2 water hoses.

      Note

      Apply insulating tape to the pipes and in the disconnected hoses or cover the pipes and hoses with plastic bags to prevent entry of foreign matter.

    2. Remove the 6 bolts and radiator assembly.