FRONT DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01FFGE

      Detach the 2 clips and 5 claws.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01FGAO

      Detach the 3 claws and remove the front door inside handle bezel plug.

  5. REMOVE FRONT DOOR HOLE COVER


    1. Remove the front door hole cover.

  6. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01FH37

      Using a moulding remover A, detach the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01FFPI

      Remove the 3 screws.

    2. Detach the 9 clips.

    3. A01FDRBE01

      Detach the reference boss in the direction indicated by the arrow in the illustration.

    4. Using a screwdriver, detach the 4 claws and remove the front door trim board.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Reference Boss
      *2 Protective Tape

    5. Disconnect each connector.

    6. A01FJ58

      Disconnect the front door lock remote control cable and front door inside locking cable.

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION


    1. A01FGD0

      Remove the front door No. 1 stiffener cushion.

  9. REMOVE FRONT DOOR TRIM COVER LH


    1. A01FEZ1

      Detach the 5 clips and remove the front door trim cover.

  10. REMOVE DOOR FRAME GARNISH LH


    1. A01FEJH

      Detach the 2 clips and remove the door frame garnish.

  11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A01FGWZ

      Remove the front door inner glass weatherstrip.

  12. REMOVE FRONT DOOR ARMREST SET BRACKET LH


    1. A01FGPM

      Remove the 2 screws and front door armrest set bracket.

  13. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01FDR7

      Pull out the front door lock remote control cable and front door inside locking cable from the front door service hole cover, and then remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the front door panel.

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door window regulator so that the front door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the power window regulator master switch assembly with front door armrest base panel.

    6. A01FHAT

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass to fall.

    7. A01FGPDE01

      Remove the front door glass as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the front door glass.

  15. REMOVE FRONT DOOR GLASS RUN LH


    1. A01FHUX

      Remove the front door glass run.

  16. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A01FIUI

      Remove the 2 bolts.

    2. Detach the guide and remove the front door rear lower frame.

  17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    1. A01FDTU

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover together with the front door lock cylinder.

  18. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. Disconnect the connector.

    2. A01FFTEE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    3. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

    4. Remove the door lock wiring harness seal from the front door lock assembly.

  19. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01FI9YE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Remove the front door lock remote control cable.

  20. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01FHNNE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Detach the 3 claws and open the cover.

    2. A01FFXYE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Remove the front door inside locking cable.