FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. REMOVE FRONT DOOR SCUFF PLATE LH


    1. Place your hands on the inner portion of the front door scuff plate LH and detach the 2 claws labeled A, 6 claws labeled B and 2 claws labeled C in the order shown in the illustration.

    2. Raise the front door scuff plate LH to detach the 4 clips on the outer side and remove it.

      A01FFCRE01
      Text in Illustration
      *1 Claw A *2 Claw B
      *3 Claw C - -

  3. REMOVE REAR DOOR SCUFF PLATE LH


    1. Place your hands on the inner portion of the rear door scuff plate LH and detach the 2 claws labeled A, 6 claws labeled B and 2 claws labeled C in the order shown in the illustration.

    2. Raise the rear door scuff plate LH to detach the 4 clips on the outer side and remove it.

      A01FDD4E01
      Text in Illustration
      *1 Claw A *2 Claw B
      *3 Claw C - -

  4. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01FEZT

      Detach the 6 hooks and remove the seat belt anchor cover cap LH.

    2. Operate the power seat switch assembly and move the front seat assembly so that the nut for the anchor of the front seat outer belt assembly LH can be removed.

    3. A01FGKS

      Remove the nut and disconnect the anchor of the front seat outer belt assembly LH.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  6. REMOVE LOWER CENTER PILLAR GARNISH LH

    A01FHIJ

    1. Pull both sides of the lower center pillar garnish LH outward to detach the 2 claws.

    2. Detach the 5 clips and 2 guides and remove the lower center pillar garnish LH.

  7. REMOVE UPPER CENTER PILLAR GARNISH LH

    A01FHNG

    1. Remove the 2 screws.

    2. Detach the clip.

    3. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish LH.

  8. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01FDR0

      Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

    2. A01FI7XE01
      Text in Illustration
      *1 Pretensioner Connector

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disconnect the connector (w/o Pre-crash Safety System) or 2 connectors (w/ Pre-crash Safety System).

    4. Remove the 2 bolts and front seat outer belt assembly LH.

  9. REMOVE FRONT SEAT BELT RETRACTOR COVER LH

  10. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A01FFT3

      Remove the 2 bolts.

    2. Disengage the guide and remove the front shoulder belt anchor adjuster assembly.