POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01FGAO

      Detach the 3 claws and remove the front door inside handle bezel plug.

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT UPPER ARMREST BASE PANEL LH (for Driver Side)


    1. A01FFGE

      Detach the 2 clips and 5 claws.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT UPPER ARMREST BASE PANEL RH (for Front Passenger Side)


    1. A01FHGM

      Using a moulding remover B, detach the 2 clips, 3 guides and 5 claws and remove the power window regulator switch assembly with front upper base panel RH.

    2. Disconnect the connector and armrest base panel assembly.

  6. REMOVE FRONT DOOR HOLE COVER


    1. Remove the front door hole cover.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01FH37

      Using a moulding remover A, detach the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01FFPI

      Remove the 3 screws.

    2. Detach the 9 clips.

    3. A01FDRBE01

      Detach the reference boss in the direction indicated by the arrow in the illustration.

    4. Using a screwdriver, detach the 4 claws and remove the front door trim board.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Reference Boss
      *2 Protective Tape

    5. Disconnect each connector.

    6. A01FJ58

      Disconnect the front door lock remote control cable and front door inside locking cable.

  9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A01FGWZ

      Remove the front door inner glass weatherstrip.

  10. REMOVE FRONT DOOR ARMREST SET BRACKET LH


    1. A01FGPM

      Remove the 2 screws and front door armrest set bracket.

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01FDR7

      Pull out the front door lock remote control cable and front door inside locking cable from the front door service hole cover, and then remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the front door panel.

  12. REMOVE DOOR FRAME GARNISH LH


    1. A01FEJH

      Detach the 2 clips and remove the door frame garnish.

  13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door window regulator so that the front door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the power window regulator master switch assembly with front door armrest base panel.

    6. A01FHAT

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass to fall.

    7. A01FGPDE01

      Remove the front door glass as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the front door glass.

  14. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A01FFBWE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.

    3. Remove the 5 bolts and front door power window regulator.

    4. Remove the temporary bolt from the front door window regulator.

  15. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01FHVV

      Using a T25 "TORX" driver, remove the 3 screws and power window regulator motor assembly LH.