SHIFT LEVER INSTALLATION


  1. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY


    1. Install the transmission floor shift assembly with the 4 bolts.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }

    2. Connect the 3 connectors and 5 clamps to the transmission floor shift assembly.

  2. INSTALL NO. 1 CONSOLE BOX DUCT


    1. Install the No. 1 console box duct with the 2 clips.

  3. CONNECT CENTER AIRBAG SENSOR ASSEMBLY

    Click here

  4. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


    1. A01FHCCE03

      Turn the transmission control shaft lever RH of the park/neutral position switch assembly counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.

    2. A01FICTE01

      Temporarily install the floor shift gear shifting rod sub-assembly with the nut.

    3. Tighten the nut while lightly pushing the lever rearward.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }
      Text in Illustration
      *a Rear

      Note

      Do not push the shift lever too hard.

  5. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR


    1. Install the front No. 1 floor heat insulator with the 4 nuts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  6. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. w/ Protector:

      Tech Tips

      Only perform this procedure when replacement of the front No. 1 exhaust pipe protector is necessary.


      1. Install the front No. 1 exhaust pipe protector and exhaust pipe protector stay with the 2 bolts and 2 nuts.

        Torque:
        11 N*m  { 107 kgf*cm, 8 ft.*lbf }

      2. Install the clamp with the bolt.

        Torque:
        11 N*m  { 107 kgf*cm, 8 ft.*lbf }
    2. A01FIIAE01

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum free length
      38.5 mm (1.52 in.)

      Tech Tips

      If the free length is less than the minimum, replace the compression spring.

    3. Install the 2 new gaskets to the front exhaust pipe assembly.

    4. A01FFE4E17
      Text in Illustration
      *1 Front Exhaust Pipe Assembly
      *2 Gasket
      *3 Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe assembly.

      Note


      • Be careful with the installation direction of the gasket.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    5. Install 2 new gaskets and the front exhaust pipe with 4 new nuts, 8 bolts and 4 compression springs.

      Torque:
      for exhaust manifold side
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }
      for tailpipe side
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  7. CONNECT HEATED OXYGEN SENSOR


    1. for Bank 2 Sensor 2:


      1. A01FFFE

        Before installing the heated oxygen sensor, twist the sensor wires counterclockwise 4 turns.

      2. A01FIUAE01
        Text in Illustration
        *1 Fulcrum Length

        Using SST, connect the heated oxygen sensor to the front exhaust pipe assembly.

        SST
        09224-00010
        Torque:
        without SST
        44 N*m  { 449 kgf*cm, 32 ft.*lbf }
        with SST
        40 N*m  { 408 kgf*cm, 30 ft.*lbf }

        Tech Tips


        • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification Click here.

        • Make sure SST and the wrench are connected in a straight line.

      3. After installing the sensor, check that the sensor wire is not twisted.

        If the sensor wire is twisted, reinstall the sensor.

      4. Connect the grommet of the heated oxygen sensor.

    2. for Bank 1 Sensor 2:


      1. A01FFFE

        Before installing the heated oxygen sensor, twist the sensor wires counterclockwise 4 turns.

      2. A01FDYRE01
        Text in Illustration
        *1 Fulcrum Length

        Using SST, connect the heated oxygen sensor to the front exhaust pipe assembly.

        SST
        09224-00010
        Torque:
        without SST
        44 N*m  { 449 kgf*cm, 32 ft.*lbf }
        with SST
        40 N*m  { 408 kgf*cm, 30 ft.*lbf }

        Tech Tips


        • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification Click here.

        • Make sure SST and the wrench are connected in a straight line.

      3. After installing the sensor, check that the sensor wire is not twisted.

        If the sensor wire is twisted, reinstall the sensor.

      4. Connect the grommet of the heated oxygen sensor.

  8. INSTALL FRONT CENTER FLOOR BRACE


    1. Install the front center floor brace with the 2 clips, 6 bolts and 2 nuts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  9. INSTALL NO. 2 REAR FLOOR BOARD SUB-ASSEMBLY


    1. Install the No. 2 rear floor board sub-assembly with the 4 grommets and 7 clips.

  10. INSTALL NO. 1 REAR FLOOR BOARD SUB-ASSEMBLY


    1. Install the No. 1 rear floor board sub-assembly with the 4 grommets and 7 clips.

  11. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.

    2. Start the engine and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R.

      If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

  12. INSPECT FOR EXHAUST GAS LEAK