CRUISE CONTROL SYSTEM Cruise Control Switch Circuit

DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the circuit control switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM

A01FDGIE05

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING GTS (CRUISE CONTROL MAIN SWITCH)


    1. Check the Data List for proper functioning of the cruise control main switch Click here.

      Cruise Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      CCS Main SW M-CPU Cruise control switch signal (Main CPU) / ON or OFF

      ON: Cruise control switch is on

      OFF: Cruise control switch is off

      		 -
      Cancel Switch Cancel switch signal / ON or OFF

      ON: CANCEL switch is on

      OFF: CANCEL switch is off

      		 -
      SET/COAT Switch -/SET switch signal / ON or OFF

      ON: -/SET switch is on

      OFF: -/SET switch is off

      		 -
      RES/ACC Switch +/RES switch signal / ON or OFF

      ON: +/RES switch is on

      OFF: +/RES switch is off

      		 -
      OK
      When cruise control main switch operation is performed, the results are the same as above.

    NG

    INSPECT CRUISE CONTROL MAIN SWITCH Click here

    OK

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT CRUISE CONTROL MAIN SWITCH


    1. Remove the cruise control main switch Click here.

    2. Inspect the cruise control main switch Click here.


    NG

    REPLACE CRUISE CONTROL MAIN SWITCH Click here

    OK

  3. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. Remove the spiral with sensor cable sub-assembly Click here.

    2. Inspect the spiral with sensor cable sub-assembly Click here.


    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  4. INSPECT CRUISE CONTROL SWITCH WIRE

    A01FHD2E09
    Text in Illustration
    *a

    Front view of wire harness connector

    (to Spiral with Sensor Cable Sub-assembly)
    *b

    Front view of wire harness connector

    (to Cruise Control Main Switch)

    1. Disconnect the spiral cable connector.

    2. Disconnect the cruise control switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z8-3 - A-3 Always Below 1 Ω
      z8-4 - A-1 Always Below 1 Ω
      A-3 - Body ground Always 10 kΩ or higher
      A-1 - Body ground Always 10 kΩ or higher

    NG

    REPLACE CRUISE CONTROL SWITCH WIRE

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)


    1. Disconnect the N31 spiral with sensor cable sub-assembly connector.

    2. Disconnect the A21 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N31-1 (CCS) - A21-15 (CCS) Always Below 1 Ω
      N31-2 (ECC) - Body ground Always Below 1 Ω
      N31-1 (CCS) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK (for 2GR-FSE) B
      OK (for 4GR-FSE) C

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR