FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A01EXKHE01

      Engage the guide.

    2. Install the bolt <A> first, then the bolt <B> to temporarily install the front shoulder belt anchor adjuster assembly.

    3. Fully tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY


    1. A01EV7AE09
      Text in Illustration
      *1 Retractor
      *a Unlocked
      *b Locked
      *c 45°

      Before installing the front seat outer belt assembly, check the ELR function.

      Note

      Do not disassemble the retractor.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        If the result is not as specified, replace the front seat outer belt assembly.

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    1. A01EVDRE01

      Install the bolt <A> first, then the bolt <B> to temporarily install the front seat outer belt assembly.

    2. Fully tighten the 2 bolts.

      Torque:
      Bolt <A>
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
      Bolt <B>
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01EUBK

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    4. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  4. INSTALL CENTER PILLAR UPPER GARNISH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

    2. Engage the clip.

    3. Install the center pillar upper garnish LH with the 2 screws.

  5. INSTALL CENTER PILLAR LOWER GARNISH


    1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.

  6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. Install the floor anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the front seat outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  7. INSTALL LAP BELT OUTER ANCHOR COVER


    1. Engage the 3 claws to install the lap belt outer anchor cover.

  8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

    for LH Side: Click here

    for RH Side: Click here

  9. INSTALL REAR DOOR SCUFF PLATE


    1. Engage the 6 claws to install the rear door scuff plate LH.

      Tech Tips

      Engage the claws from the rear side of the scuff plate.

  10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

    for LH Side: Click here

    for RH Side: Click here

  11. INSTALL FRONT DOOR SCUFF PLATE


    1. Engage the 10 claws to install the front door scuff plate LH.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INSPECT SRS WARNING LIGHT

    Click here