INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
*1 | Clip (Black) |
*2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Note
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips.
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
w/ Television Antenna:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
w/ EC Mirror:
Connect the connector.
INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
*1 | Clip (Black) |
*2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Note
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips and 2 fasteners.
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
Connect the connector to the sliding roof drive gear assembly.
w/ Television Antenna:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
w/ EC Mirror:
Connect the connector.
INSTALL VISOR HOLDER
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
Tech Tips
Use the same procedure for the other visor holder.
INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
INSTALL VISOR BRACKET COVER (for LH Side)
Engage the 4 claws to install the visor bracket cover.
INSTALL VISOR ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL VISOR BRACKET COVER (for RH Side)
Tech Tips
Use the same procedure as for the LH side.
INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
*1 | Notch |
*2 | Alignment Mark |
Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
Note
After installation, check that the corners fit correctly.
INSTALL ASSIST GRIP SUB-ASSEMBLY
Put an assist grip sub-assembly together as shown in the illustration.
Engage the 2 clips to install the assist grip sub-assembly.
Engage the 4 claws to install the 2 assist grip covers
Tech Tips
Use the same procedure for the RH side.
INSTALL REAR ASSIST GRIP ASSEMBLY LH
Put an rear assist grip assembly LH together as shown in the illustration.
Engage the 2 clips to install the rear assist grip assembly LH.
Engage the 4 claws to install the 2 assist grip covers
INSTALL REAR ASSIST GRIP ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL SPOT LIGHT ASSEMBLY
Connect the connector.
*a | Front |
Engage the 4 claws to install the spot light assembly.
INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
Connect the connector.
Engage the 4 clips to install the roof console box assembly.
INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
Connect the connector.
Engage the 4 clips to install the roof console box assembly.
INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
Engage the 2 claws to install the rain sensor cover.
INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
except TMMR Made:
Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.
Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration and engage the 2 claws to install the cover.
for TMMR Made:
Engage the 2 claws to temporarily install the inner rear view mirror stay holder cover.
Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration to engage the 2 guides and install the cover.
INSTALL INSTRUMENT PANEL SAFETY PAD
INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat Click here
for Power Seat Click here
INSTALL FRONT SEAT ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL ROOF SIDE INNER GARNISH LH
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)
Engage the guide, claw and 2 clips.
Install the rear seat side garnish LH with the bolt.
INSTALL CENTER PILLAR UPPER GARNISH LH
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.
Engage the clip.
Install the center pillar upper garnish LH with the 2 screws.
INSTALL CENTER PILLAR LOWER GARNISH LH
Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Install the floor anchor of the front seat outer belt assembly with the bolt.
Check if the ELR locks.
Note
The check should be performed with the front seat outer belt assembly installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Engage the 3 claws to install the lap belt outer anchor cover.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
*1 | Alignment Mark (Red) |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
Note
After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE LH
Engage the 6 claws to install the rear door scuff plate LH.
Tech Tips
Engage the claws from the rear side of the scuff plate.
INSTALL ROOF SIDE INNER GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR SEAT SIDE GARNISH RH (for Reclining Seat Type)
Tech Tips
Use the same procedure as for the LH side.
INSTALL CENTER PILLAR UPPER GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL CENTER PILLAR LOWER GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
*1 | Alignment Mark (Blue) |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
Note
After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Place the rear side seatback assembly LH in the cabin.
Note
Be careful not to damage the vehicle body.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.
INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Place the rear side seatback assembly RH in the cabin.
Note
Be careful not to damage the vehicle body.
Engage the hook to install the rear side seatback assembly RH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.
INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
Engage the claw to install a new rear seat cushion lock hook.
Note
Rear seat cushion lock hooks must not be reused.
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
Place the rear seat cushion assembly in the cabin.
Note
Be careful not to damage the vehicle body.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the connector.
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
Note
When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.
INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Place the rear seatback assembly LH in the cabin.
Note
Be careful not to damage the vehicle body.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly LH with the 2 bolts.
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly LH.
Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.
INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Place the rear seatback assembly RH in the cabin.
Note
Be careful not to damage the vehicle body.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly RH with the 2 bolts.
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly RH.
INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)
Place the center seatback assembly in the cabin.
Note
Be careful not to damage the vehicle body.
Engage the hook.
Install the center seatback assembly with the 2 bolts.
Connect the connector.
INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)
Place the rear seatback assembly LH in the cabin.
Note
Be careful not to damage the vehicle body.
Install the rear seatback assembly LH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.
INSTALL REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)
Place the rear seatback assembly RH in the cabin.
Note
Be careful not to damage the vehicle body.
Install the rear seatback assembly RH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the rear seat belt to the rear seat shoulder belt guide.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly RH.
INSTALL REAR SEATBACK COVER (for Reclining Seat Type)
Engage the 4 claws to install the 2 rear seatback covers.
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)
Engage the claw to install a new rear seat cushion lock hook.
Note
Rear seat cushion lock hooks must not be reused.
Tech Tips
Use the same procedure as for the LH side.
INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)
Place the rear seat cushion assembly in the cabin.
Note
Be careful not to damage the vehicle body.
Connect the 2 seat heater connectors.
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
Note
When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the seat cushion assembly.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for Reclining Seat Type)
INSTALL REAR SEAT HEADREST ASSEMBLY
INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
Note
If there is any damage, replace the garnish clip with a new one.
Install the front pillar garnish clip to front pillar garnish LH.
Tech Tips
Install the front pillar garnish clip so that it faces as shown in the illustration.
Engage the 2 guides as shown in the illustration.
Engage the 2 clips to install the front pillar garnish LH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
*1 | Alignment Mark (Yellow) |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
Note
After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 10 claws to install the front door scuff plate LH.
INSTALL FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
*1 | Alignment Mark (White) |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
Note
After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure as for the LH side.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT SRS WARNING LIGHT