AUDIO AND VISUAL SYSTEM(for Radio and Display Type), Diagnostic DTC:B1579

DTC Code DTC Name
B1579 Voice Recognition Microphone Disconnected

DESCRIPTION

Microphone signal from the telephone microphone assembly is sent to the radio and display assembly.

Also, power is supplied from the radio and display assembly to the telephone microphone assembly.

If microphone signal is disconnected, this DTC is stored.

This DTC is stored when a malfunction occurs in a connected device.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.

  • Telephone microphone assembly

  • Radio and display assembly"

WIRING DIAGRAM

A005H24E43
*a (Shielded)
*b MAP LIGHT ASSEMBLY (MICROPHONE AMPLIFIER ASSEMBLY)
*c RADIO AND DISPLAY ASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips

For vehicles equipped with an Extension Module, refer to optional equipment's manuals.

PROCEDURE


  1. CHECK MICROPHONE (OPERATION CHECK)


    1. Enter the "Microphone & Voice Recognition Check" screen Click here.

    2. A005LT2

      When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

      OK
      Check result is normal.

    OK

    REPLACE RADIO AND DISPLAY ASSEMBLY Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - MAP LIGHT ASSEMBLY)


    1. Disconnect the F47 radio and display assembly connector.

    2. Disconnect the L8 map light assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Switch Condition Specified Condition
      F47-6 (SNS2) - L8-4 (SNS2) Always Below 1 Ω
      F47-4 (MACC) - L8-1 (MACC) Always Below 1 Ω
      F47-5 (MIN+) - L8-2 (MCO+) Always Below 1 Ω
      F47-19 (MIN-) - L8-3 (MCO-) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Switch Condition Specified Condition
      F47-6 (SNS2) - Body ground Always 10 kΩ or higher
      F47-4 (MACC) - Body ground Always 10 kΩ or higher
      F47-5 (MIN+) - Body ground Always 10 kΩ or higher
      F47-19 (MIN-) - Body ground Always 10 kΩ or higher
      F47-18 (SGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK RADIO AND DISPLAY ASSEMBLY


    1. Reconnect the F47 radio and display assembly connector.

    2. A005LLJE01
      Text in Illustration
      *a

      Component with harness connected

      Radio and Display Assembly

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F47-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F47-18 (SGND) - Body ground Always Below 1 Ω
      F47-19 (MIN-) - Body ground Always Below 1 Ω

    NG

    REPLACE RADIO AND DISPLAY ASSEMBLY Click here

    OK

  4. CHECK MICROPHONE AMPLIFIER ASSEMBLY


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      L8-4 (SNS2) - L8-3 (MCO-) Always Below 1 Ω

    NG

    REPLACE MICROPHONE AMPLIFIER ASSEMBLY Click here

    OK

  5. CHECK MICROPHONE AMPLIFIER ASSEMBLY


    1. Reconnect the F47 radio and display assembly connector.

    2. Reconnect the L8 map light assembly connector.

    3. Turn the ignition switch to ACC.

    4. A005JYSE02
      Text in Illustration
      *a

      Component with harness connected

      (Map Light Assembly (Microphone Amplifier Assembly))

      Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-) of the L8 map light assembly connector.

    5. Check the waveform of the telephone microphone assembly using the oscilloscope.

      Result
      Result Proceed to
      A waveform synchronized with the voice input to the map light assembly is output A
      A waveform synchronized with the voice input to the map light assembly is not output B

    A

    REPLACE RADIO AND DISPLAY ASSEMBLY Click here

    B

    REPLACE MICROPHONE AMPLIFIER ASSEMBLY Click here