ANTI-LOCK BRAKE SYSTEM, Diagnostic DTC:C1425

DTC Code DTC Name
C1425 Open in Stop Light Switch Circuit

DESCRIPTION

The brake actuator assembly (skid control ECU) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC NO. DTC Detection Condition Trouble Area
C1425 When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit continues for 3 seconds or more.

  • STOP fuse

  • Stop light switch

  • Stop light switch circuit

  • Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

A005I5LE03

CAUTION / NOTICE / HINT

Note


  • When replacing the brake actuator assembly (skid control ECU) or deceleration sensor, be sure to perform deceleration sensor 0 point calibration and CVT oil pressure calibration after performing AT/CVT learned values initialization.

    for K310 Click here

    for K411 Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Perform the test mode procedure after the initialization (perform the test mode start only after the brake actuator assembly (skid control ECU) is replaced).

    Tech Tips

    By performing the test mode start, the identification code of the brake actuator assembly (skid control ECU) is re-registered.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC (Skid Control ECU)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    4. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

      OK
      The intelligent tester displays ON or OFF according to brake pedal operation.

    NG

    INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE TERMINAL) Click here

    OK

  2. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs Click here.

    3. Start the engine.

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is recorded Click here.

      Result
      Result Proceed to
      DTC (C1425) is not output A
      DTC (C1425) is output (for LHD) B
      DTC (C1425) is output (for RHD) C

      Tech Tips

      If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    A

    CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

    C

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

  3. INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE TERMINAL)


    1. A005MI1E01
      Text in Illustration
      *A for 1NZ-FE
      *B except 1NZ-FE
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the A37 or A38 stop light switch assembly connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A37-2 - Body ground Always 11 to 14 V
      A38-2 - Body ground Always 11 to 14 V

    4. Reconnect the A37 or A38 stop light switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    OK

  4. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Remove the stop light switch assembly Click here.

    2. Inspect the stop light switch assembly Click here.


    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  5. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. A005KTJE01
      Text in Illustration
      *A except LHD with CVT
      *B for LHD with CVT
      *a

      Front view of wire harness connector

      (to brake actuator assembly (skid control ECU))

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the A55 or A57 brake actuator assembly (skid control ECU) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      except LHD with CVT
      Tester Connection Switch Condition Specified Condition
      A55-28 (STP) - Body ground

      Stop light switch ON

      (Brake pedal depressed)

      		 11 to 14 V

      Stop light switch OFF

      (Brake pedal released)

      		 Below 1.5 V
      for LHD with CVT
      Tester Connection Switch Condition Specified Condition
      A57-28 (STP) - Body ground

      Stop light switch ON

      (Brake pedal depressed)

      		 11 to 14 V

      Stop light switch OFF

      (Brake pedal released)

      		 Below 1.5 V

    5. Reconnect the A55 or A57 brake actuator assembly (skid control ECU) connector.

      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

    C

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here