STOP AND START SYSTEM, Diagnostic DTC:P062F

DTC Code DTC Name
P062F Internal Control Module EEPROM Error

DESCRIPTION

The engine stop and start ECU stores the number of starter assembly operations, air conditioning information, and the deceleration sensor zero point learning results.

If the engine stop and start ECU cannot write the number of starter assembly operations, air conditioning information, or the deceleration sensor zero point learning results, it stores DTC P062F, blinks the stop and start cancel indicator light, and prohibits stop and start control.

DTC No. DTC Detection Condition Trouble Area
P062F

Any of the following conditions are met (1 trip detection logic):


  • Air conditioning information cannot be written

  • The deceleration sensor zero point learning value cannot be written

  • The number of starter operations was not successfully written to the EEPROM.

 Engine stop and start ECU

Tech Tips


  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

  • Check the number of starter operations.


  1. Check if the Stop and Start system operates normally.

    Tech Tips

    If the battery terminal has been disconnected, the stop and start will be prohibited. In this case, drive the vehicle for 15 to 40 minutes to permit the stop and start operation.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, allow the engine to stop due to stop and start system control (with the shift lever in D).

    5. Release the brake pedal to allow the engine to restart (with the shift lever in D).

CAUTION / NOTICE / HINT

Note


  • If the engine stop and start ECU is being replaced, register the previously recorded number of starter operations into the new engine stop and start ECU Click here.

  • After the engine stop and start ECU is replaced or after an air conditioner kit is installed, clear the A/C information stored in the engine stop and start ECU Click here.

  • After the engine stop and start ECU or airbag sensor assembly (yaw rate sensor) is replaced, initialize and calibrate 0 point of deceleration sensor Click here.

Tech Tips


  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs Click here.

  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting Click here.

PROCEDURE


  1. PERFORM REGISTRATION (ECU EXCHANGE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

    5. According to the GTS display, download the previous status (the number of starter operations) from the engine stop and start ECU to the GTS.


    NEXT

  2. CLEAR DTC


    1. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    2. Clear the DTCs.


    NEXT

  3. PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, etc)


    1. Clear the number of starter operations.


      1. Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.

    2. Clear the air conditioning information.


      1. Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.

    3. Clear the zero point calibration data of the deceleration sensor.


      1. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.


    NEXT

  4. PERFORM REGISTRATION (ECU EXCHANGE)


    1. Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

    2. According to the prompts on the GTS screen, write the information to the engine stop and start ECU.

    3. Perform air conditioning information learning.

      Tech Tips

      When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed.

    4. Perform deceleration sensor zero point calibration.


      1. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.


    NEXT

  5. CHECK DTC OUTPUT


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, allow the engine to stop due to Stop and Start system control (with the shift lever in D).

    5. Release the brake pedal to allow the engine to restart (with the shift lever in D).

    6. Check for DTCs.

    7. Check the number of starter operations.

      Result
      Result Proceed to
      DTC is not output A
      DTC P062F is output B

    A

    END

    B

    REPLACE ENGINE STOP AND START ECU Click here