STOP AND START SYSTEM, Diagnostic DTC:P0560

DTC Code DTC Name
P0560 System Voltage

DESCRIPTION

The engine stop and start ECU detects malfunctions based on +B terminal voltage and VB voltage characteristics when the VB- circuit is open. If the VB- circuit is open, the engine stop and start ECU stores DTC P0560 and blinks the stop and start cancel indicator light.

DTC No. DTC Detection Condition Trouble Area
P0560

The following condition continues for 1 second or more (1 trip detection logic):


  • VB voltage is below the threshold of the VB circuit open judgment voltage.

  • Harness or connector

  • Engine stop and start ECU

  1. After troubleshooting, perform the following steps to recheck for DTCs.

    Tech Tips


    • If the battery terminal has been disconnected, the stop and start will be prohibited. In this case, drive the vehicle for 15 to 40 minutes to permit the stop and start operation.

    • Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    6. Stop the vehicle, allow the engine to stop due to stop and start system control and wait for 1 seconds or more (with the shift lever in D).

    7. Release the brake pedal to allow the engine to restart (with the shift lever in D).

    8. Check that no DTCs are output Click here.

  2. Check if the Stop and Start system operates normally.

    Tech Tips

    If the battery terminal has been disconnected, the stop and start will be prohibited. In this case, drive the vehicle for 15 to 40 minutes to permit the stop and start operation.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, allow the engine to stop due to stop and start system control (with the shift lever in D).

    5. Release the brake pedal to allow the engine to restart (with the shift lever in D).

WIRING DIAGRAM

A005HT7E02

CAUTION / NOTICE / HINT

Note


  • If the engine stop and start ECU is being replaced, register the previously recorded number of starter operations into the new engine stop and start ECU Click here.

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU Click here.

  • After the engine stop and start ECU or airbag sensor assembly (yaw rate sensor) is replaced, initialize and calibrate 0 point of deceleration sensor Click here.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN RELAY)


    1. A005MABE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Engine Stop and Start ECU)

      Disconnect the A72 engine stop and start ECU connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A72-5 (+B) - A72-8 (GND) Ignition switch ON 9.5 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)


    1. Disconnect the A73 engine stop and start ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A73-17 (VB-) - Body ground Always Below 1 Ω

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR