INTELLIGENT PARKING ASSIST SYSTEM, Diagnostic DTC:C1627

DTC Code DTC Name
C1627 Vehicle Height Sensor Voltage is Low or High

DESCRIPTION

The rear height control sensor sub-assembly RH and headlight leveling ECU assembly are connected to the parking assist ECU. The parking assist ECU shares the vehicle height signals received from the rear height control sensor sub-assembly RH with the lighting system (auto leveling). The headlight leveling ECU assembly supplies power to the rear height control sensor sub-assembly RH via the parking assist ECU. This DTC is stored when the parking assist ECU judges that the power supply voltage for the rear height control sensor sub-assembly RH is too low or too high.

DTC No. DTC Detection Condition Trouble Area
C1627

  • Height control sensor voltage is low

  • Height control sensor voltage is high

  • Harness or connector

  • Headlight leveling ECU assembly

  • Parking assist ECU

WIRING DIAGRAM

A01J8NDE01

INSPECTION PROCEDURE

Note


  • When "System initializing" message is displayed on the navigation receiver assembly after the battery terminal disconnected, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed Click here.

  • When the headlight leveling ECU assembly is replaced, perform initialization for the lighting system Click here

  • If initialization is necessary while performing an inspection, perform initialization first and then proceed to the next step.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1627 is output A
      No DTC is output B

      Tech Tips


      • If the power source voltage output by the headlight leveling ECU assembly is abnormal, the headlight leveling warning light may come on.

      • If the DTC is not output again when rechecking for DTCs, it may have been stored due to a temporarily abnormal voltage.

      • If DTC C1627 is output frequently, duplicate the problem symptoms and perform the inspection again, even though the DTC is not output when rechecking for DTCs Click here.


    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - PARKING ASSIST ECU)


    1. Disconnect the A48 connector from the headlight leveling ECU assembly.

    2. Disconnect the L65 connector from the parking assist ECU.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A48-12 (SBR) - Body ground Always 10 kΩ or higher
      A48-21 (SGR) - Body ground Always 10 kΩ or higher
      A48-12 (SBR) - L65-15 (HB+) Always Below 1 Ω
      A48-21 (SGR) - L65-27 (HGND) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HEADLIGHT LEVELING ECU ASSEMBLY


    1. Reconnect the A48 connector to the headlight leveling ECU assembly.

    2. Disconnect the L65 connector from the parking assist ECU.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L65-15 (HB+) - L65-27 (HGND) Power switch on (IG) 4.75 to 5.25 V

    NG

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY - PARKING ASSIST ECU)


    1. Disconnect the L65 connector from the parking assist ECU.

    2. Disconnect the S3 connector from the rear height control sensor sub-assembly RH.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L65-16 (HB1) - Body ground Always 10 kΩ or higher
      L65-14 (HG1) - Body ground Always 10 kΩ or higher
      L65-16 (HB1) - S3-3 (SHB) Always Below 1 Ω
      L65-14 (HG1) - S3-1 (SHG) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY


    1. Reconnect the L65 connector to the parking assist ECU.

    2. Disconnect the S3 connector from the rear height control sensor sub-assembly RH.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S3-3 (SHB) - S3-1 (SHG) Power switch on (IG) 4.75 to 5.25 V

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

    REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH Click here