PARKING BRAKE PEDAL (for RHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01J956

      Install the parking brake control pedal assembly with the 2 bolts and nut.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
    2. A01J9HP

      Connect the parking brake switch connector.

    3. Engage the wire harness clamp.

    4. A01JCRTE01
      Text in Illustration
      *1 Fulcrum Length

      Using SST, install the bolt (A).

      SST
      09961-00950
      Torque:
      Without SST
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
      With SST
      9.4 N*m  { 96 kgf*cm, 83 in.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • This torque value is effective when SST is parallel to the torque wrench.

    5. Install the No. 1 parking brake cable assembly with the 4 bolts.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
    6. Engage the clamp.

    7. A01JD7RE02
      Text in Illustration
      *1 Lock Nut

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. A01JC5TE01
      Text in Illustration
      *1 Turn
      *2 Hold

      Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    1. A01JD5T

      Engage the 2 claws to install the No. 2 air duct sub-assembly.

  4. INSTALL NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    1. A01JCBY

      Install the No. 3 belt anchor reinforcement subassembly with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }
  5. INSTALL NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    1. A01JBGY

      Install the No. 2 belt anchor reinforcement subassembly with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }
  6. INSTALL YAW RATE AND ACCELERATION SENSOR


    1. A01JCSV

      Connect the yaw rate and acceleration sensor connector.

      Note

      Make sure that the yaw rate and acceleration sensor connector is connected securely.

    2. Install the yaw rate and acceleration sensor with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Do not damage the yaw rate and acceleration sensor.

      • Make sure that the yaw rate and acceleration sensor is installed securely.

      • Do not use dropped or damaged parts.

      • Keep the contact surfaces of the yaw rate and acceleration sensor and the body free of foreign matter.

      • Make sure that the sensor is facing the correct direction.

  7. INSTALL FRONT SEAT ASSEMBLY LH

    Tech Tips

    Refer to the instructions for Installation of the front seat assembly Click here.

  8. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  9. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  10. ADJUST PARKING BRAKE PEDAL TRAVEL


    1. Remove the No. 2 instrument panel under cover sub-assembly.

      Tech Tips

      This is symmetrical to the LHD model Click here.

    2. Completely release the parking brake pedal.

    3. A01JAITE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 11 notches at 300 N (31 kgf, 67.5 lbf)
    5. A01JAITE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    6. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    7. Check whether the parking brake drags or not.

    8. Install the No. 2 instrument panel under cover sub-assembly.

      Tech Tips

      This is symmetrical to the LHD model Click here.

  11. INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.