REAR DOOR LOCK REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  3. REMOVE DECK FLOOR BOX RH


    1. Fold back the rear No. 2 floor board.

    2. Remove the deck floor box RH Click here.

  4. REMOVE REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. A0040W5

      Disengage the 2 claws and remove the rear No. 3 floor board upper plate.

  5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A00401M

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.

  7. REMOVE DOOR ASSIST GRIP COVER


    1. A003ZX2

      Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.

  8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A0041MN

      Disengage the 7 claws and 2 guides.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  9. REMOVE REAR DOOR ARMREST COVER


    1. A0041EU

      Remove the rear door armrest cover.

  10. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A0043YGE02
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A00429Z

      Remove the 2 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    6. A00437P

      Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

    7. for 8 Speakers:


      1. Disconnect the connector.

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A00416C

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.

  12. REMOVE REAR DOOR TRIM BRACKET


    1. A0040UH

      Remove the 2 screws and rear door trim bracket.

  13. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A0043E5

      Disconnect the 2 connectors.

    2. Disengage the clamp.

    3. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through the rear door service hole cover.

    4. Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  14. REMOVE REAR DOOR GLASS RUN


    1. A0043F9

      Remove the rear door glass run.

  15. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A0043SQ

      Remove the screw.

    2. Remove the bolt and rear door window guide sub-assembly.

  16. REMOVE REAR DOOR REAR GUIDE SEAL


    1. A004411E01
      Text in Illustration
      *1 Temporary Screw

      Loosen the temporary screw.

    2. Remove the 2 screws and rear door rear guide seal.

    3. Remove the temporary screw from the rear door rear guide seal.

  17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) auxiliary battery terminal and rear power window regulator switch assembly.

    2. Connect the rear power window regulator motor connector.

    3. Move the rear door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

    5. Disconnect the rear power window regulator switch assembly and rear power window regulator motor connector.

    6. A00416K

      Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.

      Note


      • After the bolts are removed, do not allow the door glass to fall.

      • Do not damage the door glass.

  18. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY (w/o Double Locking System)


    1. A0042R3

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A0040N3

      Remove the door lock wiring harness seal from the rear door lock with motor assembly.

  19. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY (w/ Double Locking System)


    1. A0041AK

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A003ZYQ

      Remove the door lock wiring harness seal from the rear door lock with motor assembly.

  20. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)


    1. A00418U

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A00426X

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)


    1. A0042DD

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A0041DL

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)


    1. A0042WO

      Using a screwdriver, disengage the 4 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A0043SO

      Remove the rear door inside locking cable assembly as shown in the illustration.

  23. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)


    1. A0044B5

      Using a screwdriver, disengage the 4 claws as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A0042CA

      Remove the rear door inside locking cable assembly as shown in the illustration.