REMOVE REAR NO. 2 FLOOR BOARD
Using a clip remover, remove the 2 clips.
Disengage the 3 fasteners and remove the rear No. 2 floor board.
REMOVE REAR NO. 3 FLOOR BOARD
Remove the rear No. 3 floor board.
REMOVE DECK FLOOR BOX RH
Disengage the claw and 4 guides and remove the deck floor box RH.
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 10 claws and remove the front door scuff plate LH.
REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board LH.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
REMOVE FRONT PILLAR GARNISH LH
When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.
*1 | Front Pillar Garnish Clip |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Tech Tips
Make the front pillar garnish LH hang down from the front pillar garnish clip.
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.
Note
Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Tech Tips
Tape the needle-nosed pliers tip before use.
*1 | Protective Tape |
Disengage the 3 guides.
Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).
Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.
*1 | Adhesive Tape |
*2 | Protective Cover |
*3 | Curtain Shield Airbag Assembly |
Protect the curtain shield airbag assembly.
Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.
Note
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 7 claws and remove the rear door scuff plate LH.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
Disengage the 3 claws and remove the lap belt outer anchor cover.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Remove the bolt and disconnect the floor end of the front seat outer belt assembly.
REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish LH.
REMOVE CENTER PILLAR GARNISH LH
Remove the screw.
Using a clip remover, disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.
REMOVE FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE COWL SIDE TRIM BOARD RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
Tech Tips
Use the same procedure described for the LH side.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE CENTER PILLAR LOWER GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE CENTER PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR SEAT CUSHION ASSEMBLY
*1 | Front Hook |
*2 | Rear Hook |
Disengage the front hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
Dimension | Measurement |
---|---|
a | 100 mm (3.94 in.) or less |
Note
Follow the instructions below carefully as the cushion frame can be deformed easily.
Choose a front hook to disengage first. Place your hands near the front hook as shown in the illustration. Then lift the seat cushion to disengage the front hook.
Repeat the above procedure for the other hook.
Disengage the 2 rear hooks of the rear seat cushion assembly from the rear seatback assembly.
Remove the rear seat cushion assembly.
Note
Be careful not to damage the vehicle body.
REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Remove the bolt.
*1 | Fastener |
Disengage the fastener.
Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.
REMOVE REAR SIDE SEATBACK ASSEMBLY RH
Remove the bolt.
*1 | Fastener |
Disengage the fastener.
Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.
REMOVE UPPER INSTRUMENT PANEL ASSEMBLY
REMOVE TONNEAU COVER ASSEMBLY
Remove the tonneau cover assembly.
REMOVE REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY
Remove the rear No.4 floor board sub-assembly.
REMOVE DECK FLOOR BOX LH
Tech Tips
Use the same procedure described for the RH side.
REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY
Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.
REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY
Disengage the claw and 3 clips, and remove the rear No. 1 floor board sub-assembly.
REMOVE REAR NO. 1 FLOOR BOARD
Fold the rear seatback assembly LH forward.
*1 | Fastener |
Disengage the fastener.
Fold the rear seatback assembly LH forward.
*1 | Fastener |
Disengage the fastener.
Using a clip remover, remove the clip.
Disengage the 3 fasteners and remove the rear No. 1 floor board.
REMOVE DECK TRIM SERVICE HOLE COVER
Disengage the 4 claws.
Disengage the 4 guides and remove the deck trim service hole cover.
REMOVE REAR DECK TRIM COVER
Disengage the 4 claws and remove the rear deck trim cover.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
Remove the 2 bolts.
Disengage each guide and remove the 2 luggage hold belt striker assemblies.
REMOVE TONNEAU COVER HOLDER CAP (for LH Side)
*1 | Protective Tape |
Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
Tech Tips
Tape the screwdriver tip before use.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Remove the screw.
Disengage the 7 claws and 2 clips.
Disconnect the connector and remove the deck trim side panel assembly LH.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH
Disengage the 9 clips and remove the roof side inner garnish assembly LH.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
Tech Tips
Use the same procedure described for the LH side.
REMOVE TONNEAU COVER HOLDER CAP (for RH Side)
Tech Tips
Use the same procedure described for the LH side.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Remove the screw.
Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
Disconnect the rain sensor cover as shown in the illustration.
Disengage the 2 claws and remove the rain sensor cover.
REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)
Disengage the 2 guides and slide the inner rear view mirror cover as shown in the illustration.
Disengage the 6 claws and remove the inner rear view mirror cover.
REMOVE ROOF TOP MOULDING
Using a moulding remover, disengage the 3 claws and 2 clips, and remove the roof top moulding.
REMOVE MAP LIGHT ASSEMBLY
Disengage the 4 clips and 2 guides in the order shown in the illustration.
Disconnect the connector and remove the map light assembly.
REMOVE NO. 1 ROOM LIGHT ASSEMBLY
*1 | Protective Tape |
*a | Front |
Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
*1 | Protective Tape |
*a | Front |
Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws as shown in the illustration and remove the No. 1 room light housing.
*1 | Room Light Switch Base |
Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.
REMOVE FRONT ASSIST GRIP ASSEMBLY
*1 | Protective Tape |
*a | Allow the covers to come off slightly |
Using a clip remover, disengage the 4 claws.
Note
Do not forcibly pry the assist grip covers to prevent them from being deformed.
Tech Tips
Gently pry on the assist grip covers as shown in the illustration to remove them.
Tape the clip remover tip before use.
Pull off the 2 assist grip covers by hand.
Disengage the 2 clips and remove the front assist grip assembly.
Remove the 2 clips from the vehicle body.
Tech Tips
Use the same procedure for the other front assist grip.
REMOVE REAR ASSIST GRIP ASSEMBLY
*1 | Protective Tape |
*a | Allow the covers to come off slightly |
Using a clip remover, disengage the 4 claws.
Note
Do not forcibly pry the assist grip covers to prevent them from being deformed.
Tech Tips
Gently pry on the assist grip covers as shown in the illustration to remove them.
Tape the clip remover tip before use.
Pull off the 2 assist grip covers by hand.
Disengage the 2 clips and remove the rear assist grip assembly.
Remove the 2 clips from the vehicle body.
Tech Tips
Use the same procedure for the other rear assist grip.
REMOVE VISOR BRACKET COVER LH
Using a moulding remover, disengage the 3 claws and remove the visor bracket cover LH.
REMOVE VISOR ASSEMBLY LH
Disengage the 2 clips and remove the visor assembly LH.
REMOVE VISOR BRACKET COVER RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE VISOR ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE VISOR HOLDER
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
Tech Tips
Use the same procedure for the other visor holder.
REMOVE ROOF HEADLINING ASSEMBLY
*A | w/o Satellite Radio | *B | w/ Satellite Radio |
*C | for RHD with Rain Sensor | *D | w/ EC Mirror |
*E | for LHD with Rain Sensor | - | - |
w/ Rain Sensor:
Disconnect the rain sensor connector.
w/ EC Mirror:
Disconnect the inner rear view mirror connector.
w/ Rain Sensor or w/ EC Mirror:
Disengage the 2 clamps.
w/o Satellite Radio:
Disengage the 3 clamps and disconnect the connector from the front pillar RH.
w/ Satellite Radio:
Disengage the 3 clamps and disconnect the 2 connectors from the front pillar RH.
Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.
Disengage the 4 clamps from the front pillar LH.
Disconnect the 2 No. 1 roof wire connectors from the connector holder.
Remove the 5 clips.
Remove the roof headlining assembly from the vehicle through the back door.
Note
Do not damage the roof headlining assembly or body interior.