AIRBAG SYSTEM, Diagnostic DTC:B1632/81

DTC Code DTC Name
B1632/81 Lost Communication with Rear Airbag Sensor RH

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

The side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

DTC No. DTC Detection Condition Trouble Area
B1632/81

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

  • Side airbag sensor assembly RH malfunction

  • No. 2 side airbag sensor assembly RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Side airbag sensor assembly RH

  • No. 2 side airbag sensor assembly RH

  • Airbag sensor assembly

WIRING DIAGRAM

A01V21KE01
*a Side Airbag Sensor Assembly RH
*b No. 2 Side Airbag Sensor Assembly RH
*c Airbag Sensor Assembly

PROCEDURE


  1. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor RH and No. 2 side airbag sensor assembly RH.

      OK
      The connectors are properly connected

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  2. CHECK FLOOR WIRE (OPEN)


    1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

      A01UZ43E01
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly RH *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire *4 Connector B
      *5 Connector C *6 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      		 *b

      Front view of wire harness connector

      (to No. 2 Side Airbag Sensor Assembly RH)

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-1 (BCR+) - K20-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.


    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE (SHORT)


    1. A01UZVBE01
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-1 (BCR+) - K20-2 (BCR-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (SHORT TO B+)


    1. A01UZVBE01
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the ignition switch to ON (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K20-1 (BCR+) - Body ground Ignition switch ON (IG) Below 1 V
      K20-2 (BCR-) - Body ground Ignition switch ON (IG) Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. A01UZVBE01
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-1 (BCR+) - Body ground Always 1 MΩ or higher
      K20-2 (BCR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01V0Z9E09
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1632/81 is output. A
      DTC B1637/82 is output. B
      DTC B1632/81 or B1637/82 is not output. C

      Tech Tips

      Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  7. CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01UYHAE27
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly LH
      *2 Side Airbag Sensor RH

      Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1632/81 or B1637/82 is not output. A
      DTC B1632/81 is output. B
      DTC B1637/82 is output. C

      Tech Tips

      Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH Click here