AIRBAG SYSTEM, Diagnostic DTC:B1623/81

DTC Code DTC Name
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH*1) is composed of the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH*1.

The side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH*1 detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH*1).

DTC No. DTC Detection Condition Trouble Area
B1623/81

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

  • Side airbag sensor assembly RH malfunction

  • No. 2 side airbag sensor assembly RH malfunction*1

  • Airbag sensor assembly malfunction

  • Floor wire

  • Side airbag sensor assembly RH

  • Airbag sensor assembly

*1: w/ Curtain Shield Airbag

WIRING DIAGRAM

Click here

PROCEDURE


  1. SYSTEM CHECK


    1. Check the vehicle specifications.

      Result
      Result Proceed to
      w/ Curtain Shield Airbag A
      w/o Curtain Shield Airbag B

    B

    CHECK HISTORY DTC Click here

    A

  2. CHECK HISTORY DTC


    1. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    2. Check for history DTCs Click here.

      Result
      History DTC B1622/81 or B1632/81 is not output.

      Tech Tips

      Codes other than history DTCs B1622/81 and B1632/81 may be output at this time, but they are not related to this check.


    NG

    INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC Click here

    OK

  3. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (OPEN)


    1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

      A01V0FNE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH *2 Airbag Sensor Assembly
      *3 Floor Wire *4 Connector B
      *5 Connector C *6 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-4 (BBR+) - K20-3 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT)


    1. A01UY42E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-4 (BBR+) - K20-3 (BBR-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK FLOOR WIRE (SHORT TO B+)


    1. A01UY42E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the ignition switch to ON (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K20-4 (BBR+) - Body ground Ignition switch ON (IG) Below 1 V
      K20-3 (BBR-) - Body ground Ignition switch ON (IG) Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  7. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. A01UY42E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K20-4 (BBR+) - Body ground Always 1 MΩ or higher
      K20-3 (BBR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  8. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01V0Z9E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1623/81 is output. A
      DTC B1628/82 is output. B
      DTC B1623/81 or B1628/82 is not output. C

      Tech Tips

      Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable to the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  9. CHECK HISTORY DTC


    1. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    2. Check for history DTCs Click here.

      Result
      History DTC B1622/81 is not output.

      Tech Tips

      Codes other than history DTCs B1622/81 may be output at this time, but they are not related to this check.


    NG

    INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC Click here

    OK

  10. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  11. CHECK FLOOR WIRE (OPEN)


    1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

      A01UYBTE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH *2 Airbag Sensor Assembly
      *3 Floor Wire *4 Connector B
      *5 Connector C *6 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-2 (BBR+) - K21-1 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE FLOOR WIRE

    OK

  12. CHECK FLOOR WIRE (SHORT)


    1. A01V1B8E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-2 (BBR+) - K21-1 (BBR-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  13. CHECK FLOOR WIRE (SHORT TO B+)


    1. A01V1B8E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the ignition switch to ON (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K21-2 (BBR+) - Body ground Ignition switch ON (IG) Below 1 V
      K21-1 (BBR-) - Body ground Ignition switch ON (IG) Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  14. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. A01V1B8E02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-2 (BBR+) - Body ground Always 1 MΩ or higher
      K21-1 (BBR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  15. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01V0Z9E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1623/81 is output. A
      DTC B1628/82 is output. B
      DTC B1623/81 or B1628/82 is not output. C

      Tech Tips

      Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable to the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.


    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here