SEAT POSITION SENSOR INSTALLATION


  1. INSTALL SEAT POSITION SENSOR


    1. A01NHB7

      Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A01NGSLE12
      Text in Illustration
      *1 Seat Position Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position sensor.

      Note


      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.

      • When installing the seat position sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. A01NDEA

      Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Check that there is no looseness in the installation parts of the seat position sensor.

  2. INSTALL FRONT SEAT ASSEMBLY LH


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. When the power seat slide motor assembly has been removed:


      1. Recline the front seat assembly to the position where the front seat cushion shield assembly screw can be installed.

      2. Install the front seat cushion shield assembly Click here.

      3. Install the slide and vertical power seat switch knob Click here.

      4. Install the reclining power seat switch knob Click here.

    3. Connect each connector under the front seat assembly.

    4. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Temporarily install the front seat assembly with the 4 bolts.

    6. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    7. A01NDY9E01

      Tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    8. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    9. A01NH8BE01

      Tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  3. INSTALL REAR INNER SEAT TRACK BRACKET COVER LH


    1. A01NCSF

      Engage the 4 claws and install the rear inner seat track bracket cover as shown in the illustration.

  4. INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH


    1. A01NH00

      Engage the 4 claws to install the rear outer seat track bracket cover as shown in the illustration.

  5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    2. A01NGM8

      Engage the 2 guides and 2 claws to install the front inner seat track bracket cover as shown in the illustration.

  6. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH


    1. A01NE4U

      Engage the 2 guides and 2 claws to install the front outer seat track bracket cover as shown in the illustration.

  7. INSTALL FRONT SEAT HEADREST ASSEMBLY LH


    1. A01NCT4

      Install the front seat headrest assembly as shown in the illustration.

  8. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation.

    2. Check the seat heater operation.

      w/o Climate Control Seat System:


      1. Power switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  9. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  10. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  11. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.