REAR DOOR LOCK INSTALLATION


  1. INSTALL REAR DOOR LOCK ASSEMBLY (w/o Double Locking System)

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.


    1. A01NFKM

      Install the rear door inside locking cable assembly.

    2. A01NHFQ

      Engage the 3 claws.

    3. A01NEVH

      Install the rear door lock remote control cable assembly.

    4. A01NGZU

      Engage the claw.

    5. Apply MP grease to the sliding parts of the rear door lock assembly.

    6. A01NCYD

      Install a new door lock wiring harness seal to the rear door lock assembly.

    7. A01NEMH

      Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

    8. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    9. Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  2. INSTALL REAR DOOR LOCK ASSEMBLY (w/ Double Locking System)

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.


    1. A01NFW7

      Install the rear door inside locking cable assembly.

    2. A01NGU6

      Engage the 3 claws.

    3. A01ND2L

      Install the rear door lock remote control cable assembly.

    4. A01NDC3

      Engage the claw.

    5. Apply MP grease to the sliding parts of the rear door lock assembly.

    6. A01NCY2

      Install a new door lock wiring harness seal to the rear door lock assembly.

    7. A01NGJF

      Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

    8. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    9. Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

        Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
        Specification Waiting Time
        w/o Telematics transceiver 60 sec.
        w/ Telematics transceiver 120 sec.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    5. A01NE1QE01

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.

    6. A01ND56E01

      Install the rear door glass sub-assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

  4. INSTALL REAR DOOR REAR GUIDE SEAL


    1. A01NDT0

      Install the rear door rear guide seal with the 2 screws.

  5. INSTALL REAR DOOR WINDOW REAR GUIDE SUB-ASSEMBLY


    1. Install the temporary screw to the rear door window division bar sub-assembly.

    2. A01ND5FE01
      Text in Illustration
      *1 Temporary Screw

      Engage the claw, guide and temporarily install the rear door window rear guide sub-assembly.

    3. Install the bolt and screw.

    4. Tighten the temporary screw to install the rear door window rear guide sub-assembly.

  6. INSTALL REAR DOOR GLASS RUN


    1. A01NFW1

      Install the rear door glass run.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A01NEWSE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the 2 connectors.

  8. INSTALL REAR DOOR TRIM BRACKET


    1. A01ND0X

      Install the rear door trim bracket with the 2 screws.

  9. INSTALL REAR DOOR FRAME GARNISH


    1. A01NE8L

      Engage the clip to install the rear door frame garnish.

    2. Install the 2 clips.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01NDVD

      Engage the 4 claws and install the rear door inner glass weatherstrip as shown in the illustration.

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install 2 new rear door trim board retainers (green).

    2. A01NHOG

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. for 12 Speakers or 15 Speakers:


      1. Connect the connector.

    4. A01NG2B

      Engage the rear door trim board sub-assembly with the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.

    5. A01NG0YE02
      Text in Illustration
      *1 Rear Door Trim Board Retainer

      Engage the 7 clips, 2 rear door trim board retainers and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

  12. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01NH7OE01

      Engage the claw to install the courtesy light assembly.

  13. INSTALL REAR DOOR ARMREST COVER


    1. A01NFIQ

      Install the rear door armrest cover.

  14. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01NF2T

      Engage the 2 clips and 3 claws, and install the rear power window regulator switch assembly with rear door armrest base panel.

  15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01NH6R

      Engage the 3 claws and install the rear door inside handle bezel plug.

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  18. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here