NAVIGATION SYSTEM (for HDD) Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the display and navigation module display.

If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the resulting condition is the same as if the switch were continuously pressed. Therefore, the display and navigation module display cannot be operated using the steering pad switch assembly, and the display and navigation module display itself cannot function.

WIRING DIAGRAM

A01NFZPE01

INSPECTION PROCEDURE

Note

The vehicle is equipped with a Supplemental Restraint System (SRS). Before servicing (including removal or installation of parts), be sure to read Precaution for Supplemental Restraint System Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR


    1. A01NCTPE05
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Display and Navigation Module Display)

      Disconnect the G4 display and navigation module display connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G4-25 (SW1) - G4-23 (SWG) No switch pushed 95 to 105 kΩ
      G4-25 (SW1) - G4-23 (SWG) Seek+ switch pushed Below 2.5 Ω
      G4-25 (SW1) - G4-23 (SWG) Seek- switch pushed 312 to 345 Ω
      G4-25 (SW1) - G4-23 (SWG) Volume+ switch pushed 950 to 1050 Ω
      G4-25 (SW1) - G4-23 (SWG) Volume- switch pushed 2954 to 3265 Ω
      G4-24 (SW2) - G4-23 (SWG) No switch pushed 95 to 105 kΩ
      G4-24 (SW2) - G4-23 (SWG) MODE switch pushed Below 2.5 Ω
      G4-24 (SW2) - G4-23 (SWG) Voice switch pushed 2954 to 3265 Ω
      G4-24 (SW2) - G4-23 (SWG) On Hook switch pushed 312 to 345 Ω
      G4-24 (SW2) - G4-23 (SWG) Off Hook switch pushed 950 to 1050 Ω

    NG

    CHECK HARNESS AND CONNECTOR Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK HARNESS AND CONNECTOR


    1. A01NCTPE05

      Disconnect the G4 display and navigation module display connector.

    2. A01NDFXE04

      Disconnect the F40 spiral with sensor cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-25 (SW1) - F40-6 (AU1) Always Below 1 Ω
      G4-24 (SW2) - F40-5 (AU2) Always Below 1 Ω
      G4-23 (SWG) - F40-4 (EAU) Always Below 1 Ω
      G4-25 (SW1) - Body ground Always 10 kΩ or higher
      G4-24 (SW2) - Body ground Always 10 kΩ or higher
      G4-23 (SWG) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Display and Navigation Module Display)
      *2

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. A01NHMBE03
      Text in Illustration
      *1

      Component without harness connected

      (Spiral with Sensor Cable Sub-assembly)
      *2 Steering Pad Switch Side
      *3 Vehicle Side

      Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z5-8 (EAU) - F40-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z5-10 (AU1) - F40-6 (AU1) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z5-9 (AU2) - F40-5 (AU2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

      Note

      The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

      Tech Tips



    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  4. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the z5 steering pad switch assembly connector.

      A01NEQGE07

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      z5-10 (AU1) - z5-8 (EAU) No switch pushed 95 to 105 kΩ
      z5-10 (AU1) - z5-8 (EAU) Seek+ switch pushed Below 2.5 Ω
      z5-10 (AU1) - z5-8 (EAU) Seek- switch pushed 312 to 345 Ω
      z5-10 (AU1) - z5-8 (EAU) Volume+ switch pushed 950 to 1050 Ω
      z5-10 (AU1) - z5-8 (EAU) Volume- switch pushed 2954 to 3265 Ω
      z5-9 (AU2) - z5-8 (EAU) No switch pushed 95 to 105 kΩ
      z5-9 (AU2) - z5-8 (EAU) MODE switch pushed Below 2.5 Ω
      z5-9 (AU2) - z5-8 (EAU) Voice switch pushed 2954 to 3265 Ω
      z5-9 (AU2) - z5-8 (EAU) On Hook switch pushed 312 to 345 Ω
      z5-9 (AU2) - z5-8 (EAU) Off Hook switch pushed 950 to 1050 Ω
      Text in Illustration
      *1

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 *2 Volume+
      *3 Volume- *4 MODE
      *5 Seek- *6 Seek+
      *7 Off Hook *8 On Hook
      *9 Voice Switch - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY

    OK

    USE SIMULATION METHOD TO CHECK Click here