FRONT LOWER BALL JOINT REMOVAL

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTC(s).

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION (w/ Air Suspension)

    Note

    Be sure to read Precaution thoroughly before servicing Click here.

  2. REMOVE FRONT WHEEL

  3. REMOVE FRONT AXLE SHAFT NUT


    1. A01NDKKE01

      Using SST and a hammer, release the staked part of the front axle shaft nut.

      SST
      09930-00010

      Note

      Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

    2. While applying the brakes, remove the front axle shaft nut.

  4. SEPARATE FRONT SPEED SENSOR


    1. A01NDH3E03
      Text in Illustration
      *1 Hole
      *2 Resin Clamp

      Remove the bolt and resin clamp, and separate the front speed sensor.

      Note


      • Be sure to completely separate the front speed sensor from the front shock absorber with coil spring.

      • Be careful not to damage the front speed sensor.

      • Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.

  5. SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    1. A01NH4RE09
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

    2. A01NF0Y

      Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

      Note

      Loosen the staked part of the front axle hub nut completely, otherwise the threads of the drive shaft may be damaged.

  6. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A01NFI4

      Remove the 2 bolts and separate the front disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  7. REMOVE FRONT DISC


    1. A01NDGOE03
      Text in Illustration
      *1 Matchmark

      Remove the front disc.

      Tech Tips

      Put matchmarks on the disc and the axle hub.

  8. SEPARATE TIE ROD ASSEMBLY


    1. A01NEDV

      Remove the cotter pin and nut.

    2. A01NGHQE01

      Install SST to the tie rod end.

      SST
      09960-20010   ( 09961-02060 )

      Note

      Make sure that the upper ends of the tie rod end and SST are aligned.

    3. Using SST, separate the tie rod end from the steering knuckle.

      A01NEFDE01
      Text in Illustration
      *1 Tie the string without allowing for any slack. *2 Place the wrench here.
      SST
      09960-20010   ( 09961-02010 )

      Note


      • When securing SST to the steering knuckle, be sure to tighten SST using a string to prevent it from falling.


      • Install SST so that A and B are parallel.


      • Be sure to place a wrench on the part indicated in the illustration.


      • Do not damage the front disc brake dust cover.


      • Do not damage the ball joint dust cover.


      • Do not damage the steering knuckle.

  9. SEPARATE FRONT LOWER SUSPENSION ARM


    1. A01NE2G

      Remove the bolt and 2 nuts, and separate the front lower suspension arm from the lower ball joint.

  10. REMOVE FRONT AXLE ASSEMBLY


    1. A01NENL

      Remove the 2 bolts, 2 nuts and front axle assembly.

      Note

      When removing the nuts, keep the bolts from rotating.

  11. REMOVE FRONT LOWER BALL JOINT ASSEMBLY


    1. A01NF8D

      Secure the front axle assembly in a vise using aluminum plates.

      Note

      When using a vise, do not overtighten it.

    2. When removing the nut (Type A):


      1. A01NCLU

        Remove the clip and nut.

    3. When removing the nut (Type B):


      1. A01NF7Q

        Remove the cotter pin and nut.

    4. A01NFINE02

      Install SST to the front lower ball joint as shown in the illustration.

      SST
      09960-20010   ( 09961-02050, 09961-02050 )

      Note

      Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).

    5. Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.

      A01NDK7E02
      Text in Illustration
      *1 Apply grease *2 Apply grease
      *3 Place the wrench here *4 Turn
      SST
      09960-20010   ( 09961-02010, 09961-02050, 09961-02050 )

      CAUTION:

      Apply grease to the threads and end of the SST bolt.

      Note


      • Install SST so that A and B are parallel.

      • Be sure to place a wrench on the part indicated in the illustration.

      • Do not damage the front lower ball joint dust cover.