REAR AXLE HUB REMOVAL

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTC(s).

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION (w/ Air Suspension)

    Note

    Be sure to read Precaution thoroughly before servicing Click here.

  2. REMOVE REAR WHEEL

  3. REMOVE REAR AXLE SHAFT NUT (for AWD)


    1. A01NEQVE01

      Using SST and a hammer, release the staked part of the rear axle shaft nut.

      SST
      09930-00010

      Note

      Loosen the staked part of the nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.

    2. A01NENF

      While applying the parking brakes, remove the rear axle shaft nut from the rear drive shaft assembly.

  4. REMOVE REAR SUSPENSION ARM COVER (w/o Air Suspension)


    1. A01NFBI

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.

  5. REMOVE REAR SUSPENSION ARM COVER (w/ Air Suspension)


    1. A01NGSG

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.

  6. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01NFAZ

      Remove the 2 bolts, and separate the rear disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  7. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG


    1. Remove the parking brake shoe adjusting hole plug.

  8. REMOVE REAR DISC


    1. A01NFCBE01
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the rear disc and the axle hub.

    2. A01ND9X

      Release the parking brake and remove the rear disc.

      Tech Tips

      If the disc can not be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.

  9. SEPARATE REAR SPEED SENSOR WIRE (for 2WD)


    1. A01NHMJ

      Remove the bolt and No. 1 bracket.

    2. A01NE3KE01

      Using a screwdriver, disconnect the connector from the rear speed sensor.

      Note

      Be careful not to damage the rear speed sensor.

  10. SEPARATE REAR SPEED SENSOR (for AWD)


    1. A01NH71

      Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Clean the rear speed sensor installation hole and the contact surfaces every time the rear speed sensor is removed.

      • Do not twist or apply excessive force to the rear speed sensor during removal from the rear axle carrier sub-assembly to prevent it from being damaged.

  11. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)


    1. A01NGD7

      Remove the 4 bolts and the rear axle hub and bearing assembly from the rear axle carrier sub-assembly.

  12. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for AWD)


    1. A01NDTTE01
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.

    2. A01NF2O

      Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

      Tech Tips

      If it is difficult to separate, tap the end of the rear drive shaft assembly using a brass bar and a hammer.

    3. A01NG61

      Remove the 4 bolts and the rear axle hub and bearing assembly from the rear axle carrier sub-assembly.