PARKING BRAKE PEDAL (for LHD) REMOVAL

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing Click here.


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. PRECAUTION (w/ Air Suspension)

    Note

    Be sure to read Precaution thoroughly before servicing Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH

    Tech Tips

    Refer to the instructions for Removal of the front seat assembly Click here.

  4. REMOVE REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    Refer to the instructions for Removal of the rear console box assembly Click here.

  5. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

    Tech Tips

    Refer to the instructions for Removal of the driver side knee airbag assembly Click here.

  6. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A01NG2R

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  7. REMOVE CONSOLE BOX


    1. A01NDJA

      Remove the 5 screws <D>.

    2. A01NHTTE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 3 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  8. REMOVE REAR NO. 2 AIR DUCT


    1. A01NERU

      Turn back the front floor carpet.

    2. Remove the clip and rear No. 2 air duct.

  9. REMOVE REAR NO. 1 AIR DUCT


    1. A01NGFV

      Disengage the wire harness clamp.

    2. Remove the rear No. 1 air duct.

  10. REMOVE FRONT FLOOR FOOTREST


    1. A01NEGG

      Disengage the 2 clips to remove the front floor footrest.

  11. LOOSEN ADJUSTING NUT


    1. A01NF8OE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Remove the lock nut and loosen the adjusting nut.

  12. REMOVE CENTER FRONT FLOOR COVER


    1. A01NFS1

      Remove the 7 bolts and 2 screws.

    2. A01NGBG

      Disengage the 3 clips to remove the center front floor cover.

  13. REMOVE REAR ENGINE SERVICE COVER ASSEMBLY


    1. A01NECP

      Remove the 2 bolts and rear engine service cover assembly.

  14. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A01NCU5

      Separate the No. 3 parking brake cable assembly from the parking brake equalizer.

  15. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tech Tips

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  16. REMOVE PARKING BRAKE EQUALIZER


    1. A01NFD1

      Slide the rubber boot as shown in the illustration.

    2. A01NEC0

      Remove the parking brake equalizer from the No. 1 parking brake cable assembly as shown in the illustration.

  17. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Disconnect the connectors from the instrument panel junction block assembly and power management control ECU.

    2. A01NEWG

      Remove the 2 nuts.

    3. Disconnect the connectors from the back of the instrument panel junction block assembly.

  18. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01NENA

      Remove the 2 bolts and 2 nuts, and separate the No. 1 parking brake cable assembly.

    2. Remove the clamp.

    3. A01NHGE

      Pull out the No. 1 parking brake cable assembly toward the cabin.

    4. A01NH4B

      Disconnect the parking brake switch connector.

    5. A01NEX9

      Disengage the 2 clamps to separate the wire harness clamp.

    6. A01NDLL

      Remove the 3 nuts and parking brake control pedal assembly.