REAR DOOR BELT MOULDING (for Wagon) REMOVAL

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.


  1. REMOVE ENGINE ROOM SIDE COVER (w/ Power Window)


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

    Note


    • w/ Navigation system (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A003APQ

      Insert clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  4. REMOVE REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Remove the inside handle plate.

  5. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A003E60

      Remove the stiffener cushion.

  6. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A003B33

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  7. REMOVE DOOR ASSIST GRIP COVER LH


    1. A003ECP

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    1. A003ECP

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A003BXN

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A003D6XE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A003BQW

      Disconnect the 2 cables from the inside handle.

  10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A003D5U

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  11. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A003CKZ

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  12. REMOVE REAR DOOR GLASS RUN LH


    1. A003E0FE01

      Remove the rear door glass run.

  13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A003D71E01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  14. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A003AZJE01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A003DIM

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  16. REMOVE REAR DOOR BELT MOULDING LH

    A003CH3E01
    Text in Illustration
    *1 Protective tape
    *2 Claw A

    1. Put protective tape around the rear door belt moulding.

    2. Detach the 7 claws and remove the rear door belt moulding.

      Tech Tips

      If either of the claws labeled A is damaged, replace the rear door belt moulding with a new one.