CAN COMMUNICATION SYSTEM Short to GND in CAN Bus Line

DESCRIPTION

There may be a short circuit between the CAN bus line and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

  • Short between CAN bus line and GND

  • ECM

  • Brake actuator assembly (VSC ECU)

  • Parking brake with bracket actuator assembly (electric parking brake ECU)

  • Certification ECU*1

  • Air conditioning amplifier assembly

  • Spiral cable sub-assembly (steering angle sensor)

  • Yaw rate sensor

  • Main body ECU (instrument panel junction block assembly)

  • Center airbag sensor assembly

  • Power management control ECU*1, *2

  • Power steering ECU assembly

  • Combination meter assembly

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

  • No. 4 junction connector

WIRING DIAGRAM

A006SHPE03
A006VBSE04

INSPECTION PROCEDURE

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  2. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    1. Disconnect the D90 No. 3 junction connector connector.

    2. A006SIRE39
      Text in Illustration
      *1 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D8-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  3. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  4. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    1. Disconnect the A39 No. 1 junction connector connector.

    2. A006SIRE39
      Text in Illustration
      *1 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D8-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) Click here

    OK

  5. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR)


    1. A006SQSE21
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A39-8 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      A39-19 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR) Click here

    OK

  6. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A006SQSE22
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A39-10 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      A39-21 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM) Click here

    OK

    REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

  7. CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR)


    1. Disconnect the A42 brake actuator assembly (VSC ECU) connector.

    2. A006SQSE23
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A39-8 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      A39-19 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (CANH, CANL)

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY (VSC ECU) Click here

  8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    1. Disconnect the A40 ECM connector.

    2. A006SQSE22
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 1 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A39-10 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      A39-21 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher
      Result
      Result Proceed to
      OK (for 1AD-FTV) A
      OK (for 2AD-FTV) B
      OK (for 2AD-FHV) C
      NG D

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

    A

    REPLACE ECM Click here

  9. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A006SQSE25
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *2 Front view of DLC3

      Disconnect the G39 No. 2 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G39-1 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      G39-12 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

  10. CONNECT CONNECTOR


    1. Reconnect the A39 No. 1 junction connector connector.


    NEXT

  11. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

    A006SIRE39
    Text in Illustration
    *1 Front view of DLC3

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D8-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) Click here

    OK

  12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - PARKING BRAKE WITH BRACKET ACTUATOR)


    1. A006SQSE26
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G39-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      G39-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (PARKING BRAKE WITH BRACKET ACTUATOR) Click here

    OK

    REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

  13. CHECK FOR SHORT TO GND IN CAN BUS WIRE (PARKING BRAKE WITH BRACKET ACTUATOR)


    1. Disconnect the I1 parking brake with bracket actuator assembly (electric parking brake ECU) connector.

    2. A006SQSE27
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 2 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G39-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      G39-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING BRAKE WITH BRACKET ACTUATOR (CANH, CANL)

    OK

    REPLACE PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY (ELECTRIC PARKING BRAKE ECU) Click here

  14. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    1. A006SQSE28
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Disconnect the D90 No. 3 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-10 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-21 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

    OK

  15. CONNECT CONNECTOR


    1. Reconnect the G39 No. 2 junction connector connector.

    2. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  16. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE)


    1. Disconnect the D91 No. 4 junction connector connector.

    2. A006SIRE39
      Text in Illustration
      *1 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D8-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR) Click here

    OK

  17. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

    Note

    For vehicles without a battery current sensor and an entry and start system, go to "Check for Short in CAN Bus Wires (No. 4 Junction Connector - Combination Meter)".


    1. A006SQSE29
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 4 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Result
      Tester Connection Switch Condition Specified Condition
      D91-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D91-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU) Click here

    OK

  18. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER)


    1. A006SQSE30
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 4 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Result
      Tester Connection Switch Condition Specified Condition
      D91-2 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D91-13 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER) Click here

    OK

    REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR

  19. CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    1. Disconnect the D75 power management control ECU connector.

    2. A006SQSE31
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 4 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D91-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D91-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  20. CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER)


    1. Disconnect the D66 combination meter assembly connector.

    2. A006SQSE32
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 4 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D91-2 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D91-13 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (CANH, CANL)

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

  21. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    1. A006SQSE33
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 4 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D91-1 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D91-12 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

    OK

  22. CONNECT CONNECTOR


    1. Reconnect the D91 No. 4 junction connector connector.


    NEXT

  23. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)

    Note

    For vehicles without an entry and start system, go to "Check for Short in CAN Bus Wire (No. 3 Junction Connector - Power Steering ECU)".


    1. A006SQSE34
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-2 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-13 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  24. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU)


    1. A006SQSE35
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  25. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    1. A006SQSE36
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-4 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-15 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  26. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - SPIRAL CABLE)


    1. A006SQSE37
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-5 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-16 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  27. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR)


    1. A006SQSE38
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-17 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  28. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A006SQSE39
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-8 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-19 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  29. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    1. A006SQSE40
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-9 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-20 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

    REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR

  30. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  31. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU)


    1. Disconnect the D54 certification ECU connector.

    2. A006SQSE41
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-2 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-13 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

    OK

    REPLACE CERTIFICATION ECU

  32. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  33. CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU)


    1. Disconnect the D50 power steering ECU assembly connector.

    2. A006SQSE42
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-3 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-14 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)

    A

    REPLACE POWER STEERING ECU ASSEMBLY Click here

  34. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  35. CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER)


    1. Disconnect the D47*1 or D101*2 air conditioning amplifier connector.


      • *1: for Automatic Air Conditioning System

      • *2: for Manual Air Conditioning System and w/o Air Conditioning System

    2. A006SQSE43
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-4 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-15 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  36. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  37. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SPIRAL CABLE)


    1. Disconnect the D71 spiral cable sub-assembly (steering angle sensor) connector.

    2. A006SQSE44
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-5 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-16 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL CABLE (CANH, CANL)

    OK

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

  38. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  39. CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR)


    1. Disconnect the D69 yaw rate sensor connector.

    2. A006SQSE45
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-6 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-17 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)

    OK

    REPLACE YAW RATE SENSOR Click here

  40. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  41. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)


    1. Disconnect the D81 main body ECU (instrument panel junction block assembly) connector.

    2. A006SQSE46
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-8 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-19 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  42. CONNECT CONNECTOR


    1. Reconnect the D90 No. 3 junction connector connector.


    NEXT

  43. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    1. Disconnect the D10 center airbag sensor assembly connector.

    2. A006SQSE47
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to No. 3 Junction Connector)
      *2 Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D90-9 (CANH) - D8-4 (CG) Ignition switch off 200 Ω or higher
      D90-20 (CANL) - D8-4 (CG) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here