CAN COMMUNICATION SYSTEM, Diagnostic DTC:U0208

DTC Code DTC Name
U0208 Lost Communication with "Seat Control Module A"

DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the position control ECU assembly.

  • Power source circuit of position control ECU assembly

  • Position control ECU assembly

  • Position control ECU assembly branch wire or connector

For vehicles w/ Seat Position Memory System.

WIRING DIAGRAM

A003BK1E01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  2. CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU BRANCH WIRE)


    1. A003AWUE01
      Text in Illustration
      *1 for LHD
      *2 for RHD
      *3

      Front view of wire harness connector

      (to Position Control ECU Assembly)

      Disconnect the O26*1 or O16*2 position control ECU assembly connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Switch Condition Specified Condition
      O26-40 (CANH) - O26-39 (CANL) Ignition switch off 54 to 69 Ω
      for RHD
      Tester Connection Switch Condition Specified Condition
      O16-40 (CANH) - O16-39 (CANL) Ignition switch off 54 to 69 Ω

    NG

    REPAIR OR REPLACE POSITION CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

    OK

  3. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU - BATTERY AND BODY GROUND)


    1. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. A003CATE01
      Text in Illustration
      *1 for LHD
      *2 for RHD
      *3

      Front view of wire harness connector

      (to Position Control ECU Assembly)

      Disconnect the O26*1, O27*1 or O16*1, O17*2 position control ECU assembly connectors.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      O26-21 (GND2) - Body ground Always Below 1 Ω
      O27-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      O16-21 (GND2) - Body ground Always Below 1 Ω
      O17-1 (GND) - Body ground Always Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      O26-1 (SYSB) - Body ground Always 11 to 14 V
      O27-5 (+B) - Body ground Always 11 to 14 V
      Standard Voltage
      for RHD
      Tester Connection Condition Specified Condition
      O16-1 (SYSB) - Body ground Always 11 to 14 V
      O17-5 (+B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POSITION CONTROL ECU ASSEMBLY Click here