RADIO RECEIVER REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00EB81E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00E7QBE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

      A006SZ5E02
      Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  6. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A003B2YE02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00E7Y2E01

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00E70T

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00E8WSE01

  10. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL


    1. A00E6R6E01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and hook.

    3. A00E7A7

      Detach the 3 claws and 3 hooks.

    4. Detach the 6 clips.

    5. A00EA2S

      Remove the panel register. Then disconnect the connector and detach the clamp.

  11. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET


    1. A003DP4

      Remove the 4 screws.

    2. A003C30

      Pull the radio receiver to detach the 4 clips on the backside of the radio receiver.

    3. Disconnect the connectors and remove the radio receiver.

  12. REMOVE NO. 1 RADIO BRACKET


    1. A003BCX

      Remove the 3 screws and bracket.

  13. REMOVE NO. 2 RADIO BRACKET


    1. A003B8Z

      Remove the 3 screws and bracket.