STEERING WHEEL INSTALLATION


  1. INSTALL TRANSMISSION SHIFT SWITCH ASSEMBLY (w/ Shift Paddle Switch)


    1. A003AGSE01
      Text in Illustration
      *1 Shift Paddle Switch
      *2 Bracket

      Install the 2 shift paddle switches and 2 brackets with the 4 screws.

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }

      CAUTION:

      Make sure that the brackets are securely installed.

    2. A003CHRE01
      Text in Illustration
      *1 Switch Wire

      Connect the 2 switch wire connectors to the shift paddle switches.

    3. A003B1C

      Install the connector to the steering wheel assembly.

    4. Install the clamp to the steering wheel assembly.

  2. INSTALL STEERING SHAKE DAMPER

    A003AVC

    1. Install the steering shake damper with the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

  3. INSTALL STEERING PAD SWITCH ASSEMBLY

    A003B0N

    1. Attach the 2 claws and 4 pins to install the steering pad switch.

    2. Install the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

    3. Connect the connector.

  4. INSTALL CRUISE CONTROL SWITCH WIRE (w/ Cruise Control System)

  5. INSTALL CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)


    1. A003ARR

      Install the switch with the 2 screws.

    2. Connect the connector.

  6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  7. ADJUST SPIRAL CABLE


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A003BHW

      Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

      CAUTION:

      Do not turn the spiral cable by the airbag wire harness.

    4. A003E5M

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable by the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  8. INSTALL STEERING WHEEL ASSEMBLY


    1. A003C9PE01
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  9. INSTALL STEERING PAD


    1. A003BC1

      Support the steering pad with one hand.

    2. Connect the connector to the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    3. Connect the horn connector.

    4. Attach the 2 springs to install the steering pad.

  10. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A003DD4

      Attach the 2 claws to install the steering wheel cover.

  11. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A003E2XE01
      Text in Illustration
      *1 w/o Cruise Control System
      *2 w/ Cruise Control System

      Attach the 2 claws to install the steering wheel cover.

  12. INSPECT STEERING WHEEL CENTER POINT

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.