ROOF HEADLINING (for Wagon) REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • w/ Navigation system (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    A003ATB

    1. Detach the 2 front hooks of the seat cushion from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat for the other hook.

    2. Detach the 2 rear hooks of the seat cushion from the seatback.

      Note

      Be careful not to damage the vehicle body.

  4. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    A003CVN

    1. Remove the bolt and disconnect the rear seat 3 point type belt anchor.

    2. A003AHX

      Using a screwdriver, detach the claw to open the cap of the rear seat shoulder belt guide.

    3. Remove the seat belt from the belt guide.

    4. A003CZ2E01

      Remove the bolt, and then remove the side seatback LH as shown in the illustration.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A00EB62

    1. Pull the lever and remove the tonneau cover.

  7. REMOVE ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    A00E89C

    1. Push the 2 buttons and remove the room partition net.

  8. REMOVE LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  9. REMOVE LOWER DECK TRIM SIDE BOARD RH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  10. REMOVE DECK BOARD ASSEMBLY

    A00E8VK

    1. Detach the clip and 2 guides, and remove the deck board.

  11. REMOVE DECK BOARD SUB-ASSEMBLY

    A00E7OL

    1. Pull the lever and remove the deck board.

  12. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Detach the clip and remove the No. 3 deck board.

      A00EAE7E01
  13. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 3 deck board.

  14. REMOVE REAR DECK FLOOR BOX


    1. Detach the 7 guides and remove the rear deck floor box.

      A00EANXE01
  15. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    A00E6UC

    1. Remove the 3 bolts and floor side rail.

  16. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00E8MU

    1. Detach the 2 clips and 3 guides, and remove the deck side trim cover.

  18. REMOVE NO. 1 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 2 deck side trim cover.

  19. REMOVE NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    A00EAH0

    1. Detach the 3 claws and remove the No. 6 deck side trim cover.

  20. REMOVE NO. 5 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 6 deck side trim cover.

  21. REMOVE ROPE HOOK ASSEMBLY (w/o Deck Rail)

    A00E9GF

    Tech Tips

    Use the same procedure for all the rope hooks.


    1. Remove the bolt and rope hook.

  22. REMOVE DECK FLOOR BOX LH

    A00EB3Y

    1. Remove the bolt.

    2. Detach the 5 guides and remove the deck floor box.

  23. REMOVE DECK FLOOR BOX RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE REAR FLOOR FINISH PLATE

    A00E6JD

    1. Detach the 4 clips and remove the rear floor finish plate.

  25. REMOVE FRONT DECK FLOOR BOX

    A00E6UE

    1. Remove the 2 clips.

    2. Detach the 4 guides and remove the front deck floor box.

  26. REMOVE FRONT DOOR SCUFF PLATE LH

    A00EBB8

    1. Detach the 6 claws and clip, and remove the rear door scuff plate.

  27. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE COWL SIDE TRIM BOARD LH

    A00E7SS

    1. Detach the clip, claw and guide, and remove the cowl side trim board.

  29. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00E9QE

    1. Remove the front door opening trim weatherstrip.

  31. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE REAR DOOR SCUFF PLATE LH

    A00EBB8

    1. Detach the 6 claws and clip, and remove the rear door scuff plate.

  33. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A00E9KT

    1. Remove the rear door opening trim weatherstrip.

  35. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE BACK DOOR WEATHERSTRIP

    A00E8VT

    1. Remove the back door weatherstrip.

  37. REMOVE FRONT PILLAR GARNISH LH

    A00EB2JE01
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish hang down from the front pillar garnish clip.

    2. A00E6XVE01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    3. Detach the 2 guides and remove the front pillar garnish.

    4. A00EAAQE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  38. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE LOWER CENTER PILLAR GARNISH LH

    A00E8QB

    1. Detach the 2 claws and 3 clips, and remove the lower center pillar garnish.

  40. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. REMOVE LAP BELT OUTER ANCHOR COVER

    A00EBEO

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Detach the 3 claws and remove the lap belt outer anchor cover.

  42. REMOVE CENTER PILLAR GARNISH LH

    A00E9F7

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A00EAN3

      Remove the 2 screws.

    3. Detach the clip.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

  43. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  44. REMOVE NO. 2 DECK SIDE TRIM HOOK

    A00E8YJ

    Tech Tips

    Use the same procedure to remove the No. 2 deck side trim hook on the other side.


    1. Remove the screw and No. 2 deck side trim hook.

  45. REMOVE INNER ROOF SIDE GARNISH CAP LH

    A00E73ME01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the inner roof side garnish cap.

    2. Using a screwdriver, detach the 2 claws and remove the inner roof side garnish cap.

      Tech Tips

      Tape the screwdriver tip before use.

  46. REMOVE INNER ROOF SIDE GARNISH CAP RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and clip.

    2. Detach the 7 clips and 3 claws.

    3. Pass the fuel lid opener cable through the panel, disconnect the connector, and then remove the deck trim side panel.

      A00EAYWE01
      Text in Illustration
      *1 Fuel Lid Opener Cable - -
  48. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the bolt and clip.

    2. Detach the 7 clips and 3 claws, and remove the deck trim side panel.

      A00EB2T
  49. REMOVE INNER ROOF SIDE GARNISH LH

    A00EBD0E01
    Text in Illustration
    *1 Clip A

    1. Detach the 6 clips (do not detach clip A).

    2. Pull the inner roof side garnish in the direction indicated by the arrow in the illustration and remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  50. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the upper instrument panel sub-assembly Click here.

  52. REMOVE COIN BOX ASSEMBLY


    1. A006VL1

      Slightly bend the upper part of the coin box to release the 2 stoppers and open the coin box until it is horizontal.

    2. A006V0B

      Pull the coin box toward the rear of the vehicle to detach the 2 hinges and remove the coin box.

  53. REMOVE MAP LIGHT ASSEMBLY

    A00E83T

    1. Using a moulding remover, detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  54. REMOVE FRONT ROOF TOP GARNISH (w/ Lane Keeping Assist System)

    A006WP8E01

    1. Detach the clip and 2 claws and remove the front roof top garnish.

      Note

      When removing the rain sensor cover, do not apply force to the lane recognition camera sensor assembly areas labeled "X".

  55. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    A00EALI

    1. Detach the 4 claws.

    2. Disconnect the connector and remove the No. 1 room light.

  56. REMOVE NO. 1 ROOM LIGHT COVER (for Cold Area)

    A00E9SA

    1. Remove the No. 1 room light cover.

  57. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    A003EJ0

    1. Detach the 2 claws and remove the inner rear view mirror stay holder cover as shown in the illustration.

  58. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A006V8F

      Detach the 3 claws and remove the rain sensor cover.

  59. REMOVE VISOR ASSEMBLY LH

    A00E6WC

    1. Using a moulding remover, detach the 2 clips and remove the visor.

  60. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  61. REMOVE VISOR HOLDER

    A00E77GE01

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  62. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A00E8M8E02

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00EA1Y

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the assist grip.

    4. Remove the 2 clips from the vehicle body.

  63. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A00E6U0E02

    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00E83Y

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the rear assist grip.

    4. Remove the 2 clips from the vehicle body.

  64. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  65. REMOVE REAR ROOM PARTITION NET HOOK LH

    A00E722

    1. Remove the screw.

    2. Detach the 2 claws and remove the rear room partition net hook.

  66. REMOVE REAR ROOM PARTITION NET HOOK RH

    Tech Tips

    Use the same procedure described for the LH side.

  67. REMOVE ROOF HEADLINING ASSEMBLY

    A00EAZV

    Tech Tips

    Before removing the roof headlining, move the front seats and rear seat to the positions shown in the illustration.


    1. A00E78Z

      w/ EC Mirror:

      Disconnect the EC mirror connector.

    2. A00EAPB

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A00E6PI

      w/ Lane Keeping Assist System:

      Tech Tips


      • Use the same procedure for RHD and LHD vehicles.

      • The procedure listed below is for LHD vehicles.


      1. Disconnect the connector and detach the clamp.

    4. A00E7QS

      Disconnect the connector and 3 clamps from the front pillar RH.

    5. A00EAGM

      Remove the 2 bolts.

    6. Disconnect the 3 connectors and 3 clamps from the rear pillar RH.

    7. A00E753

      w/ Roof Sunshade System:

      Disconnect the connector from the rear pillar LH.

    8. A00E6UI

      Disconnect the 4 clamps from the front pillar LH.

    9. for LHD:


      1. A00E9R7E01

        Disconnect the 2 clamps.

      2. A00EA3YE01

        Disconnect the 2 roof wire connectors.

    10. for RHD:


      1. A00E9PYE01

        Disconnect the 2 clamps and roof wire connector.

      2. A00E8CUE01

        Disconnect the roof wire connector.

    11. w/o Roof Sunshade System:


      1. Remove the 5 clips.

        A00E7ED
    12. w/ Roof Sunshade System:


      1. Remove the 5 clips.

      2. Detach the 3 guides and 12 fasteners.

        A00E7CDE01
        Text in Illustration
        *1 Guide *2 Fastener
    13. A00E6TF

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  68. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    A00E7V6E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the front door scuff plate outside.

    2. Using a moulding remover, detach the 3 clips and remove the front door scuff plate outside.

  69. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  70. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    A00E70SE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate outside.

    2. Using a moulding remover, detach the 2 clips and remove the rear door scuff plate outside.

  71. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  72. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A00EB79

    1. Detach the 5 claws and remove the front shoulder belt anchor plate.

  73. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  74. REMOVE REAR NO. 2 SIDE RAIL SPACER LH

    A00E9RQ

    1. Detach the 2 claws and remove the No. 2 side rail spacer.

  75. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  76. REMOVE REAR NO. 3 SIDE RAIL SPACER LH

    A00E9U6

    1. Detach the 2 claws and remove the No. 3 side rail spacer.

  77. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  78. REMOVE FRONT DECK RAIL BRACKET LH (w/ Deck Rail)

    A00E7T0

    1. Remove the 2 bolts and front deck rail bracket.

  79. REMOVE FRONT DECK RAIL BRACKET RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  80. REMOVE NO. 4 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    A00E72O

    1. Remove the bolt and No. 4 luggage compartment trim bracket.

  81. REMOVE NO. 3 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 4 luggage compartment trim bracket.

  82. REMOVE NO. 2 DECK BOARD BRACKET

    A00EB1V

    1. Remove the 2 bolts and No. 2 deck board bracket.

  83. REMOVE NO. 1 DECK BOARD BRACKET

    Tech Tips

    Use the same procedure described for the No. 2 deck board bracket.

  84. REMOVE TONNEAU COVER HOLDER BRACKET LH (w/ Tonneau Cover)

    A00E6KU

    1. Remove the 2 bolts and tonneau cover holder bracket.

  85. REMOVE TONNEAU COVER HOLDER BRACKET RH (w/ Tonneau Cover)

    Tech Tips

    Use the same procedure described for the LH side.