ROOF HEADLINING (for Sedan) INSTALLATION


  1. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

    A00E9RQ

    1. Attach the 2 claws to install the No. 2 side rail spacer.

  2. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00E7OF

    1. Attach the 4 claws to install the rear side rail spacer.

  4. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00E93D

    1. Attach the 4 claws to install the front side rail spacer.

  6. INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A00EB79

    1. Attach the 5 claws to install the front shoulder belt anchor plate.

  8. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    A00EB6T

    1. Attach the 2 clips to install the rear door scuff plate outside.

  10. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    A00E85X

    1. Attach the 3 clips to install the front door scuff plate outside.

  12. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL ROOF HEADLINING ASSEMBLY

    A00E75YE01

    1. Place the roof headlining into the vehicle through the passenger door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. Attach the clip to install the roof headlining.

      A00E9PE

    3. for LHD:


      1. A00EA3YE01

        Connect the 2 roof wire connectors.

      2. A00E9R7E01

        Connect the 2 clamps.

    4. for RHD:


      1. A00E8CUE01

        Connect the roof wire connector.

      2. A00E9PYE01

        Connect the 2 clamps and connector.

    5. A00E6UI

      Connect the 4 clamps to the front pillar LH.

    6. A00E79J

      Install the antenna with the 2 bolts.

    7. Connect the clamp to the rear pillar RH.

    8. Connect the 3 connectors.

    9. A00E7QS

      Connect the 3 clamps to the front pillar RH.

    10. Connect the connector.

    11. A00E6PI

      w/ Lane Keeping Assist System:

      Tech Tips


      • Use the same procedure for RHD and LHD vehicles.

      • The procedure listed below is for LHD vehicles.


      1. Connect the connector and attach the clamp.

    12. A00EAPB

      w/ Rain Sensor:

      Connect the rain sensor connector.

    13. A00E78Z

      w/ EC Mirror:

      Connect the EC mirror connector.

  14. INSTALL SUNSHADE TRIM HOLDER

    A00EAR7E01

    1. Position the pin as shown in the illustration and install the sunshade trim holder.

  15. INSTALL ASSIST GRIP SUB-ASSEMBLY

    A00E801

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Assemble the assist grip as shown in the illustration.

    2. A00E79P

      Install the assist grip.

  16. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    A00EAWM

    1. Assemble the rear assist grip as shown in the illustration.

    2. A00E8GB

      Install the rear assist grip.

  17. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. INSTALL VISOR HOLDER

    A00E8N0

    Tech Tips

    Use the same procedure to install the visor holder on the other side.


    1. Attach the 2 claws.

    2. Push in the visor holder as shown in the illustration.

  19. INSTALL VISOR ASSEMBLY LH

    A00EAS8

    1. Attach the 2 clips to install the visor.

  20. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. A006V8F

      Attach the 3 claws to install the No. 1 rain sensor cover.

  22. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A003AV4

      Attach the 2 claws and install the inner rear view mirror stay holder cover.

  23. INSTALL NO. 1 ROOM LIGHT COVER (for Cold Area)

    A00E9SA

    1. Install the No. 1 room light cover.

  24. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    A00EALI

    1. Connect the connector.

    2. Attach the 4 clips to install the No. 1 room light.

  25. INSTALL FRONT ROOF TOP GARNISH (w/ Lane Keeping Assist System)


    1. Attach the 2 claws and clip to install the front roof top garnish.

      A00EAPCE01

      Note

      When removing the rain sensor cover, do not apply force to the lane recognition camera sensor assembly areas labeled "X".

  26. INSTALL MAP LIGHT ASSEMBLY

    A00EB9Q

    1. Connect the connector.

    2. Attach the 4 clips to install the map light.

  27. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Install the lower instrument panel sub-assembly Click here.

  28. INSTALL CONSOLE BOX ASSEMBLY


    1. w/o Console Box Lid:

      Install the console box assembly Click here.

    2. w/ Console Box Lid:

      Install the console box assembly Click here.

  29. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below the for LHD vehicles.


    1. Install the upper instrument panel sub-assembly Click here.

  30. INSTALL INNER ROOF SIDE GARNISH LH

    A00E7N4E01
    Text in Illustration
    *1 Clip A

    1. Install 2 new clips labeled A to the inner roof side garnish.

    2. Attach the 5 clips to install the inner roof side garnish.

  31. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL CENTER PILLAR GARNISH LH

    A00EAN3

    1. Pass the front seat outer belt floor anchor through the center pillar garnish.

    2. Attach the clip to install the center pillar garnish.

    3. Install the 2 screws.

    4. A00E9F7

      Install the front seat outer belt floor anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

  33. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. INSTALL LAP BELT OUTER ANCHOR COVER

    A00EBEO

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Attach the 3 claws to install the lap belt outer anchor cover.

  35. INSTALL LOWER CENTER PILLAR GARNISH LH

    A00E8QB

    1. Attach the 2 claws and 3 clips to install the lower center pillar garnish.

  36. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL FRONT PILLAR GARNISH LH

    A00E7THE01
    Text in Illustration
    *1 Front Pillar Garnish Clip
    *2 Protective Tape

    1. w/ Curtain Shield Airbag:

      Remove the protective cover.

    2. Attach the 2 guides.

    3. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    4. A00EATFE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  38. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A00E7HOE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. INSTALL REAR DOOR SCUFF PLATE LH

    A00EBB8

    1. Attach the clip and 6 claws to install the front door scuff plate.

  42. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00E7D9E01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the front door opening trim weatherstrip as shown in the illustration.

  44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  45. INSTALL COWL SIDE TRIM BOARD LH

    A00E7SS

    1. Attach the clip, claw and guide to install the cowl side trim board.

  46. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. INSTALL FRONT DOOR SCUFF PLATE LH

    A00EA17

    1. Attach the 2 clips and 8 claws to install the front door scuff plate.

  48. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. A003BE1E01

      Install the claw as shown in the illustration.

    2. Install the side seatback with the bolt.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
    3. A003CVN

      Install the rear seat 3 point type belt anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt to overlap the protruding parts of the floor panel.

    4. Install the seat belt to the belt guide.

    5. Attach the claw to close the cap of the rear seat shoulder belt guide.

    6. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  50. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    A003CGQE01

    1. Attach the 2 rear hooks of the seat cushion to the seatback.

    2. Attach the 2 front hooks to install the seat cushion.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.

  52. INSTALL FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Install the front seat assembly Click here.

    2. for Power Seat:

      Install the front seat assembly Click here.

  53. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  54. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  55. INSTALL ENGINE ROOM SIDE COVER


    1. A003B3G

      Install the engine room side cover with the clip.