ROOF HEADLINING (for Sedan) REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • w/ Navigation system (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Remove the front seat assembly Click here.

    2. for Power Seat:

      Remove the front seat assembly Click here.

  4. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    A003ATB

    1. Detach the 2 front hooks of the seat cushion from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat for the other hook.

    2. Detach the 2 rear hooks of the seat cushion from the seatback.

      Note

      Be careful not to damage the vehicle body.

  6. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    A003CVN

    1. Remove the bolt and disconnect the rear seat 3 point type belt anchor.

    2. A003AHX

      Using a screwdriver, detach the claw to open the cap of the rear seat shoulder belt guide.

    3. Remove the seat belt from the belt guide.

    4. A003CZ2E01

      Remove the bolt, and then remove the side seatback LH as shown in the illustration.

  7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT DOOR SCUFF PLATE LH

    A00EA17

    1. Detach the 8 claws and 2 clips, and remove the front door scuff plate.

  9. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE COWL SIDE TRIM BOARD LH

    A00E7SS

    1. Detach the clip, claw and guide, and remove the cowl side trim board.

  11. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00E9QE

    1. Remove the front door opening trim weatherstrip.

  13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE REAR DOOR SCUFF PLATE LH

    A00EBB8

    1. Detach the 6 claws and clip, and remove the rear door scuff plate.

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A00EAF7

    1. Remove the rear door opening trim weatherstrip.

  17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE FRONT PILLAR GARNISH LH

    A00EB2JE01
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish hang down from the front pillar garnish clip.

    2. A00E6XVE01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    3. Detach the 2 guides and remove the front pillar garnish.

    4. A00EAAQE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  19. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE LOWER CENTER PILLAR GARNISH LH

    A00E8QB

    1. Detach the 2 claws and 3 clips, and remove the lower center pillar garnish.

  21. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE LAP BELT OUTER ANCHOR COVER

    A00EBEO

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Detach the 3 claws and remove the lap belt outer anchor cover.

  23. REMOVE CENTER PILLAR GARNISH LH

    A00E9F7

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A00EAN3

      Remove the 2 screws.

    3. Detach the clip.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

  24. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE INNER ROOF SIDE GARNISH LH

    A00E7N4E01
    Text in Illustration
    *1 Clip A

    1. Detach the 5 clips and remove the inner roof side garnish.

      Tech Tips

      The 2 clips labeled A remain attached to the body.

    2. Remove the 2 clips labeled A from the vehicle body.

  26. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the upper instrument panel sub-assembly Click here.

  28. REMOVE CONSOLE BOX ASSEMBLY


    1. w/o Console Box Lid:

      Remove the console box assembly Click here.

    2. w/ Console Box Lid:

      Remove the console box assembly Click here.

  29. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the lower instrument panel sub-assembly Click here.

  30. REMOVE MAP LIGHT ASSEMBLY

    A00E83T

    1. Using a moulding remover, detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  31. REMOVE FRONT ROOF TOP GARNISH (w/ Lane Keeping Assist System)

    A006WP8E01

    1. Detach the clip and 2 claws and remove the front roof top garnish.

      Note

      When removing the rain sensor cover, do not apply force to the lane recognition camera sensor assembly areas labeled "X".

  32. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    A00EALI

    1. Detach the 4 claws.

    2. Disconnect the connector and remove the No. 1 room light.

  33. REMOVE NO. 1 ROOM LIGHT COVER (for Cold Area)

    A00E9SA

    1. Remove the No. 1 room light cover.

  34. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    A003EJ0

    1. Detach the 2 claws and remove the inner rear view mirror stay holder cover as shown in the illustration.

  35. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A006V8F

      Detach the 3 claws and remove the rain sensor cover.

  36. REMOVE VISOR ASSEMBLY LH

    A00E6WC

    1. Using a moulding remover, detach the 2 clips and remove the visor.

  37. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  38. REMOVE VISOR HOLDER

    A00E77GE01

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  39. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A00E8M8E02

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00EA1Y

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the assist grip.

    4. Remove the 2 clips from the vehicle body.

  40. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A00E6U0E02

    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00E83Y

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the rear assist grip.

    4. Remove the 2 clips from the vehicle body.

  41. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. REMOVE SUNSHADE TRIM HOLDER


    1. A00E6OQE01

      Turn the pin and remove the sunshade trim holder.

  43. REMOVE ROOF HEADLINING ASSEMBLY

    A00E78Z

    1. w/ EC Mirror:

      Disconnect the EC mirror connector.

    2. A00EAPB

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A00E6PI

      w/ Lane Keeping Assist System:

      Tech Tips


      • Use the same procedure for RHD and LHD vehicles.

      • The procedure listed below is for LHD vehicles.


      1. Disconnect the connector and detach the clamp.

    4. A00E7QS

      Disconnect the connector and 3 clamps from the front pillar RH.

    5. A00E79J

      Remove the 2 bolts.

    6. Disconnect the 3 connectors and clamp from the rear pillar RH.

    7. A00E6UI

      Disconnect the 4 clamps from the front pillar LH.

    8. for LHD:


      1. A00E9R7E01

        Disconnect the 2 clamps.

      2. A00EA3YE01

        Disconnect the 2 roof wire connectors.

    9. for RHD:


      1. A00E9PYE01

        Disconnect the 2 clamps and roof wire connector.

      2. A00E8CUE01

        Disconnect the roof wire connector.

    10. Detach the clip.

      A00E9PE
    11. A00E75YE01

      Remove the roof headlining from the passenger door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  44. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    A00E7V6E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the front door scuff plate outside.

    2. Using a moulding remover, detach the 3 clips and remove the front door scuff plate outside.

  45. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    A00E70SE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate outside.

    2. Using a moulding remover, detach the 2 clips and remove the rear door scuff plate outside.

  47. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A00EB79

    1. Detach the 5 claws and remove the front shoulder belt anchor plate.

  49. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00E93D

    1. Detach the 4 claws and remove the front side rail spacer.

  51. REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  52. REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00E7OF

    1. Detach the 4 claws and remove the rear side rail spacer.

  53. REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  54. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

    A00E9RQ

    1. Detach the 2 claws and remove the No. 2 side rail spacer.

  55. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.