POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • w/ Navigation System for HDD:

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A003E60

      Remove the stiffener cushion.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A003B33

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  4. REMOVE DOOR ASSIST GRIP COVER LH


    1. A003ECP

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A003BSU

      Using moulding remover A, detach the 6 claws and the clip.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A003BXN

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A003D6XE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A003BQW

      Disconnect the 2 cables from the inside handle.

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A003D5U

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  8. REMOVE REAR DOOR FRAME GARNISH LH


    1. A003C1QE01

      Detach the 2 clips.

    2. Detach the claws and remove the rear door frame garnish.

  9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A003CKZ

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  10. REMOVE REAR DOOR GLASS RUN LH


    1. A003E0FE01

      Remove the rear door glass run.

  11. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A003D71E01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A003AZJE01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A003DIM

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  14. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. A006VFZE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator.