WINDSHIELD GLASS REMOVAL


  1. REMOVE ENGINE ROOM COVER SIDE


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • w/ Navigation System for (HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH


    1. for Sedan:

      Remove the center roof drip side finish moulding Click here.

    2. for Wagon:

      Remove the center roof drip side finish moulding Click here.

  4. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE FRONT WIPER ARM HEAD CAP


    1. A003BEK

      Using a screwdriver, remove the front wiper arm head cap.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for all front wiper arm head caps.

  6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A003CFU

      Remove the nut and the front wiper arm and blade assembly LH.

  7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A003C4X

      Remove the nut and the front wiper arm and blade assembly RH.

  8. REMOVE HOOD TO COWL TOP SEAL


    1. A003BK8

      Using a clip remover, detach the 6 clips and 2 claws and remove the hood to cowl top seal.

  9. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A003CSY

      Remove the clip.

    2. Detach the 8 claws and remove the cowl top ventilator louver RH.

  10. REMOVE COWL TOP VENTILATOR LOUVER LH


    1. A003B6G

      Remove the clip.

    2. Detach the 5 claws and remove the cowl top ventilator louver LH.

  11. REMOVE FRONT DOOR SCUFF PLATE LH

    A00EA17

    1. Detach the 8 claws and 2 clips, and remove the front door scuff plate.

  12. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE COWL SIDE TRIM BOARD LH

    A00E7SS

    1. Detach the clip, claw and guide, and remove the cowl side trim board.

  14. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00E9QE

    1. Remove the front door opening trim weatherstrip.

  16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE FRONT PILLAR GARNISH LH

    A00EB2JE01
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish hang down from the front pillar garnish clip.

    2. A00E6XVE01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    3. Detach the 2 guides and remove the front pillar garnish.

    4. A00EAAQE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  18. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE LANE RECOGNITION CAMERA SENSOR ASSEMBLY (w/ Lane Keeping Assist System)


    1. Remove the lane recognition camera sensor Click here.

  20. REMOVE MAP LIGHT ASSEMBLY

    A00E83T

    1. Using a moulding remover, detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  21. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


    1. A003DN6

      Slide and remove the inner rear view mirror.

  22. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    A003EJ0

    1. Detach the 2 claws and remove the inner rear view mirror stay holder cover as shown in the illustration.

  23. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


    1. A003DYF

      Disconnect the connector.

    2. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror.

  24. REMOVE NO. 1 RAIN SENSOR COVER (w/ Rain Sensor)


    1. A006V8F

      Detach the 3 claws and remove the rain sensor cover.

  25. REMOVE NO. 2 RAIN SENSOR COVER (w/ Rain Sensor)


    1. A006UGI

      Using a screwdriver, detach the 2 claws and remove the No. 2 rain sensor cover.

  26. REMOVE RAIN SENSOR (w/ Rain Sensor)


    1. A006W64

      Detach the 2 claws and remove the rain sensor.

      Note

      Do not touch the silicon mixture directly with a finger.

    2. A006T6J

      Disconnect the connector.

      Note

      Do not touch the silicon mixture directly with a finger.

  27. REMOVE VISOR ASSEMBLY LH

    A00E6WC

    1. Using a moulding remover, detach the 2 clips and remove the visor.

  28. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE VISOR HOLDER

    A00E77GE01

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  30. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A00E8M8E02

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00EA1Y

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the assist grip.

    4. Remove the 2 clips from the vehicle body.

  31. REMOVE ROOF HEADLINING


    1. for Sedan:

      Partially remove the roof headlining.

      Tech Tips

      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

      Refer to the following procedure Click here.

    2. for Wagon:

      Partially remove the roof headlining.

      Tech Tips

      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

      Refer to the following procedure Click here.

  32. REMOVE WINDSHIELD OUTSIDE MOULDING

    A00E9SSE03
    Text in Illustration
    *1 Cut
    *2 Vehicle Body
    *3 Moulding
    *4 Windshield glass

    1. Using a knife, cut off the moulding as shown in the illustration.

      Note

      Be careful not to damage the vehicle body.

    2. Pull the shaded area shown in the illustration by hand to remove the windshield outside moulding.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

  33. REMOVE WINDSHIELD GLASS

    A00EA73E02
    Text in Illustration
    *1 Plastic Sheet
    *2 Protective tape
    *3 Stopper
    *4 Piano Wire

    1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    2. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

      Note


      • When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      • To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.

    4. A00EBE4E07
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

      Note

      Matchmarks do not need to be placed if not reusing the glass.

    5. w/ Windshield Deicer System:

      Disconnect the windshield deicer connector.

    6. Cut through the adhesive by pulling the piano wire around the glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the glass.

    7. Disconnect the stoppers.

    8. Using suction cups, remove the glass.

  34. REMOVE NO. 2 WINDSHIELD GLASS STOPPER


    1. Using a scraper, remove the 2 stoppers.

  35. REMOVE WINDOW GLASS ADHESIVE DAM


    1. Using a scraper, remove the dam.

  36. REMOVE NO. 1 WINDSHIELD GLASS STOPPER


    1. Remove the 2 windshield glass stoppers.

  37. CLEAN VEHICLE BODY

    A00E7HRE15
    Text in Illustration
    *1 Adhesive
    *2 Vehicle Body

    1. Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with cleaner.

      Tech Tips

      Even if all the adhesive has been removed, clean the vehicle body.