VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1417

DTC Code DTC Name
C1417 IG1 Voltage Supply too High

DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is cleared when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 IG1 Voltage Supply too High

Either of the following is detected:


  1. The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.

  2. When the voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut for 0.2 seconds or more.

  • Battery

  • Charging system

  • Wire harness or connector

  • Skid control ECU (brake actuator assembly)

WIRING DIAGRAM

B0076MXE13

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK BATTERY


    1. Check the battery voltage.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Positive (+) terminal - Negative (-) terminal Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY for 2GR-FKS: Click here
    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY for 8AR-FTS: Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (+BS TERMINAL)


    1. B0076NPC14
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A94 skid control ECU (brake actuator assembly) connector.

    3. Turn the engine switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A94-38 (+BS) - Body ground Engine switch on (IG) 11 to 14 V
      A94-38 (+BS) - A94-25 (GND1) Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

    OK

  3. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Reconnect the A94 skid control ECU (brake actuator assembly) connector.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the engine switch off.

    5. Start the engine.

    6. Perform a road test.

    7. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1417 is not output. A
      DTC C1417 is output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY for LHD: Click here
    REPLACE BRAKE ACTUATOR ASSEMBLY for RHD: Click here