NAVIGATION SYSTEM, Diagnostic DTC:B15DB

DTC Code DTC Name
B15DB Telematics Transceiver Disconnected

DESCRIPTION

If the radio receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the engine switch is turned on (ACC) and the radio receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DB Telematics Transceiver Disconnected Telematics transceiver disconnected

  • Harness or connector

  • Telematics transceiver

  • Telematics transceiver power source circuit

  • Radio receiver assembly

  • Navigation ECU

  • Stop and start system*

Tech Tips

This DTC may be stored due to environmental reasons such as electrical noise or interference.

WIRING DIAGRAM

B0076NSE02

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

  • When replacing the radio receiver assembly or navigation ECU, always replace it with a new one. If a radio receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly or navigation ECU may not operate normally.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    2. Turn the engine switch off.

    3. Turn the engine switch on (IG) and wait for 90 seconds.

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER POWER SOURCE)


    1. Disconnect the O150 telematics transceiver connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O150-4 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O150-1 (+B) - O150-4 (E) Always

      11 to 14 V*1

      10.5 to 16 V*2
      O150-8 (ACC) - O150-4 (E) Engine switch on (ACC)

      11 to 14 V*1

      10.5 to 16 V*2
      O150-7 (IG2) - O150-4 (E) Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2

      • *1: w/o Stop and Start System

        *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here

    A

  3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)


    1. Disconnect the O160 radio receiver assembly connector.

    2. Disconnect the O191 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O160-10 (USBV) - O191-4 (USBV) Always Below 1 Ω
      O160-11 (USBG) - O191-2 (USBG) Always Below 1 Ω
      O160-10 (USBV) or O191-4 (USBV) - Body ground Always 10 kΩ or higher
      O160-11 (USBG) or O191-2 (USBG) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT RADIO RECEIVER ASSEMBLY


    1. Disconnect the O160 radio receiver assembly connector.

    2. B007409C17
      *a

      Component without harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O160-11 (USBG) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O160-10 (USBV) - O160-11 (USBG) Engine switch on (ACC) 4.75 to 5.25 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)


    1. Disconnect the O191 telematics transceiver connector.

    2. Disconnect the O190 navigation ECU connector.

    3. B0076U6C05
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)
      *b

      Front view of wire harness connector

      (to Navigation ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O191-1-2 (USB (USB+)) - O190-1 (USB+) Always Below 1 Ω
      O191-1-1 (USB (USB-)) - O190-2 (USB-) Always Below 1 Ω
      O191-1-3 (USB (USBS)) - O190-3 (USBS) Always Below 1 Ω
      O191-1-2 (USB (USB+)) or O190-1 (USB+) - Body ground Always 10 kΩ or higher
      O191-1-1 (USB (USB-)) or O190-2 (USB-) - Body ground Always 10 kΩ or higher
      O191-1-3 (USB (USBS)) or O190-3 (USBS) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

    2. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG) and wait for 90 seconds.

    5. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

    NG

  7. CHECK NAVIGATION ECU


    1. Replace the navigation ECU with a new one.

      Click here

    2. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG) and wait for 90 seconds.

    5. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (NAVIGATION ECU IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here