| Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|
| Steering sensor zero point calibration | Lane Departure Alert System (w/ Steering Control) | |
| Pre-collision System | ||
| Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) | Stop and Start System | |
| Steering sensor zero point calibration | Variable Gear Ratio Steering System | |
| Correct the steering angle neutral point | Parking Assist Monitor System (w/o Parallel Parking Assist Function) | |
| Servo motor initialization | Air Conditioning System |
PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
Note
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
| Replacement Part | Necessary Procedure | Effect/Inoperative Function when Necessary Procedures are not Performed | Link |
|---|---|---|---|
| ECM | Vehicle Identification Number (VIN) registration | MIL comes on | Click here for 8AR-FTS (w/ Canister Pump Module) Click here for 2GR-FKS (w/ Canister Pump Module) Click here for 2GR-FKS (w/o Canister Pump Module) |
| Vehicle Identification Number (VIN) registration | MIL comes on / - | Click here for 8AR-FTS (w/o Canister Pump Module) |
|
| Heavy Knock History | - | Click here for 8AR-FTS (w/ Canister Pump Module) Click here for 8AR-FTS (w/o Canister Pump Module) |
|
| ECU communication ID registration (Immobiliser system) | Engine start function | See Service Bulletin for the registration method. | |
for 8AR-FTS (w/ Canister Pump Module) |
Clear Heavy Knock History | - | |
for 8AR-FTS (w/ Canister Pump Module) |
Inspection after repair |
|
|
for 8AR-FTS (w/o Canister Pump Module) |
Clear Heavy Knock History | - | |
for 8AR-FTS (w/o Canister Pump Module) |
Inspection after repair |
|
|
for 2GR-FKS (w/ Canister Pump Module) |
Inspection after repair |
|
|
for 2GR-FKS (w/o Canister Pump Module) |
Inspection after repair |
|
|
| Millimeter wave radar sensor assembly | Adjust millimeter wave radar sensor assembly |
|
|
|
Adjust forward recognition camera |
|
|
| Engine stop and start ECU*5 |
|
Stop and start system | |
| Air conditioning amplifier assembly*5 |
|
||
| Starter assembly*5 Note When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced. |
Clear Number of Starter Operations | ||
| Yaw rate and acceleration sensor*5 |
|
||
| Battery*5 |
|
||
| Oil pump assembly with solenoid*5 | Check oil pump assembly solenoid | ||
for 8AR-FTS |
|
|
Click here for Initialization Click here for Registration |
for 8AR-FTS |
Perform road test to allow ECM to learn | ||
for 8AR-FTS |
|
||
for 8AR-FTS |
|
||
for 8AR-FTS |
|
||
for 2GR-FKS |
|
|
Click here for Initialization Click here for Registration |
for 2GR-FKS |
Perform road test to allow ECM to learn | ||
for 2GR-FKS |
|
||
for 2GR-FKS |
|
||
for 2GR-FKS |
|
||
| Absorber control ECU | Perform registration of vehicle identification information |
|
|
|
|
|
Click here for Initialization Click here for Registration |
| Skid control ECU (brake actuator assembly) | Perform yaw rate and acceleration sensor zero point calibration and store system information. |
|
|
| Yaw rate and acceleration sensor |
|
||
|
Perform rotation angle sensor initialization and torque sensor zero point calibration |
|
|
| Power steering ECU assembly | Assist map writing |
|
|
|
Perform actuator angle neutral point calibration and initialization |
|
|
| DRS ECU (rear steering control ECU) | Perform neutral position memorization and motor rotation angle sensor calibration |
|
|
| Rear steering link assembly or rear suspension have been removed/installed, replaced, or adjusted |
|
Steering wheel off-center | |
|
Vehicle contract setting |
|
|
|
Download necessary data | Some G-BOOK service content will be unavailable. | |
| Telematics transceiver*10 | Register vehicle information | Emergency call service | |
| Mobilephone battery*10 | Reset mobilephone battery condition | ||
| Spiral cable with sensor sub-assembly |
|
Parking assist monitor system (w/o Parallel parking assist function) | Click here for Initialization Click here for Calibration |
| Rear television camera assembly |
|
||
| Suspension, tires, etc. | Rear television camera assembly optical axis (Back camera position setting) | ||
| Blind spot monitor sensor | Blind spot monitor beam axis adjustment | DTCs are output | |
|
Re-registration of codes in the garage door opener system
|
Garage door opener system | |
|
Code registration (Immobiliser system) |
|
See Service Bulletin for the registration method. |
|
Initialization servo motor (Air conditioning system) | DTCs are output | |
|
Initialize power window control system |
|
|
|
Initialize sliding roof system |
|
|
| Headlight leveling ECU assembly*3 |
|
Headlight leveling function | |
| Headlight light control ECU sub-assembly LH*4 |
|
||
| Rear height control sensor sub-assembly | Perform headlight leveling ECU assembly initialization*3 | ||
| Perform headlight light control ECU sub-assembly LH initialization*4 |
*1: New automatic transmission's compensation code.
*2: Set the transmission compensation code of the current automatic transmission.
*3: for Single Beam Headlight
*4: for Triple Beam Headlight
*5: w/ Stop and Start System
*6: Read the compensation code from the previous ECM, then transfer it to the new ECM.
*7: w/ G-BOOK
*8: w/ Telematics Transceiver for G-BOOK
*9: w/o Telematics Transceiver for G-BOOK
*10: w/ Telematics Transceiver except G-BOOK