FUEL LID LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  3. REMOVE COWL SIDE TRIM BOARD RH (for LHD)


    1. A01CE66

      Remove the clip.

    2. Disengage the 2 clips, claw and 2 guides, and remove the cowl side trim board RH.

  4. REMOVE FRONT DOOR SCUFF PLATE RH


    1. A01CFWN

      Disengage the claw, 6 clips and 3 guides, and remove the door scuff plate assembly RH.

  5. REMOVE COWL SIDE TRIM BOARD LH (for RHD)


    1. A01CBNG

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  6. REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  7. REMOVE FRONT DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure as for the RH side Click here.

  8. REMOVE NO. 3 FLOOR CARPET MOULDING (for Manual Seat Type RH Side)


    1. A01CCSD

      Using a screwdriver, turn the clip 90° counterclockwise to release the lock, and remove the No. 3 floor carpet moulding.

  9. REMOVE FRONT SEAT LEG COVER RH (for Manual Seat Type RH Side)


    1. Lift up the seat track adjusting handle and move the seat to the foremost position.

    2. A01CE1V

      Turn back the floor carpet.

    3. A01CF35

      Disengage the 6 claws and the guide, and remove the front seat leg cover.

  10. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat Type RH Side)

  11. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat Type RH Side)


    1. A01CBJR

      Remove the 2 bolts on the rear side of the seat.

    2. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    3. A01CCZSE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and the guide, and open the cover.

    4. A01CBCYE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and the guide, and open the cover.

    5. A01CEGB

      Remove the 2 bolts on the front side of the seat.

    6. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

    7. A01CAQF

      Disconnect each connector.

    8. A01CDOK

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  12. REMOVE NO. 3 FLOOR CARPET MOULDING (for Driver Side Power Seat)


    1. A01CCSD

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  13. REMOVE FRONT SEAT LEG COVER RH (for Driver Side Power Seat)


    1. Operate the slide and vertical power seat switch knob and move the seat to the foremost position.

    2. A01CE1V

      Turn back the floor carpet.

    3. A01CF35

      Disengage the 6 claws and guide, and remove the front seat leg cover.

  14. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Driver Side Power Seat)

  15. REMOVE FRONT SEAT ASSEMBLY (for Driver Side Power Seat)


    1. The seat travel distance can be customized, this function is OFF Click here.

    2. A01CBJR

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the slide and vertical power seat switch knob and move the seat to the rearmost position.

    4. A01CCZSE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CBCYE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    6. A01CBCP

      Remove the 2 bolts on the front side of the seat.

    7. Operate the slide and vertical power seat switch knob and move the seat to the center position. Also, operate the reclining power seat switch knob and move the seatback to the upright position.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    9. A01CAQF

      Disconnect the 2 connectors.

    10. A01CFBA

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  16. REMOVE NO. 3 FLOOR CARPET MOULDING (for Manual Seat Type LH Side)


    1. A01CCWK

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  17. REMOVE FRONT SEAT LEG COVER LH (for Manual Seat Type LH Side)


    1. Lift up the seat track adjusting handle and move the seat to the foremost position.

    2. A01CBK1

      Turn back the floor carpet.

    3. A01CF94

      Disengage the 6 claws and guide, and remove the front seat leg cover LH.

  18. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat Type LH Side)

  19. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat Type LH Side)


    1. A01CCQQ

      Remove the 2 bolts on the rear side of the seat.

    2. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    3. A01CF3UE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    4. A01CCZDE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CEHR

      Remove the 2 bolts on the front side of the seat.

    6. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

    7. A01CCND

      Disconnect the 2 connectors.

    8. A01CBQW

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  20. REMOVE NO. 3 FLOOR CARPET MOULDING (for Passenger Side Power Seat)


    1. A01CCWK

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  21. REMOVE FRONT SEAT LEG COVER LH (for Passenger Side Power Seat)


    1. Operate the slide power seat switch knob and move the seat to the foremost position.

    2. A01CBK1

      Turn back the floor carpet.

    3. A01CF94

      Disengage the 6 claws and guide, and remove the front seat leg cover LH.

  22. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Passenger Side Power Seat)

  23. REMOVE FRONT SEAT ASSEMBLY (for Passenger Side Power Seat)


    1. A01CCQQ

      Remove the 2 bolts on the rear side of the seat.

    2. Operate the slide power seat switch knob and move the seat to the rearmost position.

    3. A01CCMKE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    4. A01CCEZE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CDSZ

      Remove the 2 bolts on the front side of the seat.

    6. Operate the slide power seat switch knob and move the seat to the center position. Also, operate the reclining power seat switch knob and move the seatback to the upright position.

    7. Operate the front seat power seat switch assembly to fully raise the ottoman.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    9. A01CCND

      Disconnect the 2 connectors.

    10. A01CCXM

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  24. REMOVE CONSOLE REAR END PANEL


    1. for Long Type:


      1. A01CAZG

        Disengage the 11 claws and 2 guides as shown in the illustration.

        Note

        When pushing down on the claws, be careful not to damage them.

      2. w/ Power Outlet Socket:


        1. Disconnect each connector to remove the console rear end panel.

    2. for Short Type:


      1. A01CDP2

        Disengage the 11 claws as shown in the illustration.

        Note

        When pushing down on the claws, be careful not to damage them.

  25. REMOVE CONSOLE BOX ASSEMBLY


    1. A01CFXS

      Remove the 2 bolts.

    2. A01CC2K

      Disengage the 2 guides and remove the console box assembly as shown in the illustration.

  26. REMOVE REAR DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  27. DISCONNECT NO. 1 SLIDE DOOR WEATHERSTRIP LH

  28. REMOVE LAP BELT OUTER ANCHOR COVER

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  30. REMOVE ASSIST GRIP PLUG

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  31. REMOVE NO. 2 ASSIST GRIP

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  32. REMOVE LOWER CENTER PILLAR GARNISH LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  33. REMOVE BACK DOOR STRIKER COVER


    1. A01CDGVE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and 2 guides, and remove the back door striker cover.

      Tech Tips

      Tape the screwdriver tip before use.

  34. REMOVE BACK DOOR SCUFF PLATE


    1. A01CCY0

      Remove the 4 claws, 4 clips and 2 guides, and remove the back door scuff plate.

  35. ADJUST REAR NO. 2 SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  36. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  37. REMOVE UPPER SEAT TRACK RAIL COVER LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  38. REMOVE NO. 1 SEAT TRACK LOCK PLATE COVER

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  39. REMOVE REAR NO. 2 SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  40. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the No. 2 luggage compartment trim hook and No. 1 luggage compartment trim hook Click here.

  41. REMOVE ROPE HOOK ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  42. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH (for 60/40 Split Seat Type)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  43. DISCONNECT REAR NO. 1 OUTER SEAT BELT ASSEMBLY LH (for 60/40 Split Seat Type)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  44. REMOVE DECK SIDE GARNISH LH


    1. A01CD2TE01

      Disengage the 12 claws and 4 guides, and remove the deck side garnish LH as shown in the illustration.

  45. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. Remove the clip.

    2. Disengage the 15 clips, 8 claws and 2 guides, and remove the rear quarter trim panel assembly LH.

      A01CEOA

  46. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CFFK

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and 2 guides.

    3. A01CE9QE01

      Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  47. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01CCYO

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and guide.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  48. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)


    1. A01CC11

      Disengage the 3 claws and disconnect the fuel lid lock open lever sub-assembly.

    2. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

  49. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for LHD)


    1. A01CDU8

      Disengage the 3 claws and disconnect the fuel lid lock control cable sub-assembly.

    2. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

  50. REMOVE FUEL FILLER OPENING LID LOCK SUB-ASSEMBLY (for RHD)


    1. A01CEHJE01

      Disconnect the fuel filler opening lid lock sub-assembly as shown in the illustration.

    2. Turn back the floor carpet.

    3. Disengage the 14 clamps and remove the fuel filler opening lid lock sub-assembly.

      A01CF8A

  51. REMOVE FUEL FILLER OPENING LID LOCK SUB-ASSEMBLY (for LHD)


    1. A01CEHJE01

      Disconnect the fuel filler opening lid lock sub-assembly as shown in the illustration.

    2. Turn back the floor carpet.

    3. Disengage the 9 clamps and remove the fuel filler opening lid lock sub-assembly.

      A01CG7E