SLIDE DOOR DISASSEMBLY


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Move the door inside handle knob to the lock position.

    2. A01CG64

      Using a T25 "TORX" socket wrench, remove the screw.

    3. Using a clip remover, disengage the 15 clips and 5 claws.

    4. Disconnect the connector and remove the rear door trim board sub-assembly.

  3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A01CAPN

      Disengage the 2 claws and remove the rear power window regulator switch assembly.

  4. REMOVE SLIDE DOOR WINDOW GARNISH (w/o Navigation System for HDD)


    1. A01CDVI

      Disengage the 5 clips and remove the slide door window garnish.

  5. REMOVE SLIDE DOOR WINDOW GARNISH (w/ Navigation System for HDD)


    1. A01CCFR

      Disconnect the connector.

    2. Disengage the 5 clips and remove the slide door window garnish.

  6. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (w/ Navigation System for HDD)


    1. A01CDPR

      Disengage the clamp.

    2. Disengage the 3 claws and remove the rear No. 3 speaker assembly as shown in the illustration.

      Note

      Do not touch the cone part of the speaker.

  7. REMOVE REAR DOOR FRONT WINDOW GUIDE


    1. A01CE7U

      Remove the screw.

    2. Disengage the clip and remove the rear door front window guide.

  8. REMOVE REAR DOOR GLASS WEATHERSTRIP INNER WITH GARNISH


    1. A01CD27

      Disengage the claw and remove the rear door glass weatherstrip inner with garnish.

  9. REMOVE REAR DOOR REAR GUIDE BRACKET GARNISH


    1. A01CCMB

      Disengage the clip and remove the rear door rear guide bracket garnish from the rear door glass weatherstrip inner.

  10. REMOVE SLIDE DOOR DOWN FEMALE STOPPER


    1. A01CEFD

      Remove the 2 bolts and slide door down female stop.

  11. REMOVE SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY (w/o Power Slide Door)


    1. A01CG94

      Disconnect each connector.

    2. Remove the 3 bolts.

    3. Disengage the guide.

    4. A01CCKL

      Disconnect each cable and remove the slide door lock remote control sub-assembly from the rear door panel.

  12. REMOVE SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY (w/ Power Slide Door)


    1. A01CFGL

      Disconnect each connector.

    2. Remove the 3 bolts.

    3. Disengage the guide.

    4. A01CD22

      Disconnect each cable and remove the slide door lock remote control sub-assembly from the rear door panel.

  13. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01CCSA

      Remove the 3 screws.

    2. Disconnect each rod and remove the rear door inside handle sub-assembly from the slide door lock remote control assembly.

  14. REMOVE SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY (w/ Power Slide Door)


    1. A01CG36

      Disengage the clamp.

    2. Disconnect the connector.

    3. Remove the 3 screws and remove the slide door lock release motor assembly.

  15. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CDPU

      Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.


      1. While holding the sides of the outer connector locking sleeve, slide the outer in the direction shown by the arrow.

        A01CANCE01

      2. When the connector lock is released, the connectors can be disconnected.

        Tech Tips

        Be sure to hold both outer flank sides. Holding the top and bottom will make disconnection difficult.

    4. A01CBWYE01

      Remove the bolt and door side airbag sensor.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

  16. REMOVE NO. 1 WITH BOX SPEAKER ASSEMBLY


    1. A01CE32

      Disconnect the connector.

    2. Remove the 3 bolts.

    3. Disengage the clamp and remove the No. 1 with box speaker assembly.

      Note

      Do not touch the cone part of the speaker.

  17. REMOVE SLIDE DOOR CLOSER RELAY (w/ Easy Closer)


    1. A01CESE

      Disconnect the connector.

    2. Remove the 2 screws and slide door closer relay.

  18. REMOVE REAR DOOR SCUFF PLATE


    1. Captain type rear seat:


      1. A01CFIB

        Disengage the 9 claws, 9 clips and 2 guides, and remove the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Apply protective tape to the bottom of the seat as shown in the illustration.

      2. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      3. Disengage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

      4. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      5. Disengage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration, and remove the rear door scuff plate RH.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

  19. REMOVE REAR SIDE STEP SUPPORT


    1. A01CE4SE01

      Remove the bolt and disconnect the ground wire.

    2. Remove the 2 bolts.

    3. Turn back the floor carpet.

    4. Using a clip remover, disengage the 2 clips and remove the rear side step support.

  20. REMOVE REAR DOOR NO. 1 WIRE (w/o Power Slide Door)


    1. A01CBWP

      Disconnect each connector.

    2. Remove the bolt.

    3. Disengage the clip and disconnect the rear door No. 1 wire.

    4. A01CG4BE01

      Remove the bolt and disconnect the ground wire.

    5. Disconnect each connector.

    6. Disengage the 5 clamps.

    7. Remove the 3 bolts.

    8. Disengage the 2 clips and remove the rear door No. 1 wire.

  21. REMOVE REAR DOOR NO. 1 WIRE (w/ Power Slide Door)


    1. A01CBIO

      Disconnect each connector.

    2. Disengage the clamp.

    3. Remove the bolt.

    4. Disengage the clip and disconnect the rear door No. 1 wire.

    5. A01CDZAE02

      Remove the bolt and disconnect the ground wire.

    6. Disconnect each connector.

    7. Disengage the 5 clamps.

    8. Remove the 3 bolts.

    9. Disengage the 2 clips and remove the rear door No. 1 wire.

  22. REMOVE SLIDE DOOR SERVICE HOLE COVER


    1. A01CDCU

      Disengage the 3 clamps.

    2. Remove the slide door service hole cover.

      Tech Tips

      Remove the remaining butyl tape on the door.

  23. REMOVE REAR DOOR WINDOW FRAME MOULDING

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  24. REMOVE REAR DOOR OUTSIDE MOULDING

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  25. REMOVE REAR DOOR BELT MOULDING

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  26. REMOVE REAR DOOR GLASS RUN


    1. A01CEF2

      Remove the rear door glass run.

  27. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01CC9R

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door to fall.

    2. A01CE98E01

      Remove the rear door glass sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  28. REMOVE REAR DOOR NO. 2 GLASS RUN


    1. A01CFI9

      Remove the rear door No. 2 glass run.

  29. REMOVE REAR DOOR POWER WINDOW REGULATOR ASSEMBLY


    1. A01CFL3E01

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door power window regulator assembly may fall and get damaged.

    2. Remove the 5 bolts.

    3. Remove the rear door power window regulator assembly.

    4. Remove the temporary bolt from the rear door power window regulator assembly.

  30. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01CAJC

      Using a T25 "TORX" driver, remove the 3 screws and rear power window regulator motor assembly.

  31. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A01CFG0

      Remove the 2 bolts and rear door window guide sub-assembly.

  32. REMOVE SLIDE DOOR FRONT LOCK ASSEMBLY


    1. A01CBIW

      Disconnect the rod.

    2. Using a T30 "TORX" socket wrench, remove the 4 screws and slide door front lock assembly.

  33. REMOVE REAR DOOR LOCK ASSEMBLY


    1. A01CFLY

      Disengage the clamp.

    2. Remove the bolt.

    3. Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock assembly.

  34. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. A01CCNZ

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover.

      Tech Tips

      The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  35. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01CE75

      Remove the rear door outside handle assembly as shown in the illustration.

  36. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A01CDLX

      Disengage the 3 claws to remove the rear door front outside handle pad.

  37. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A01CGCE

      Disengage the 2 claws to remove the rear door rear outside handle pad.

  38. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. A01CF59

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Disengage the claw and remove the rear door outside handle frame sub-assembly.

  39. REMOVE CENTER PILLAR UPPER END WEATHERSTRIP (w/o Power Slide Door)


    1. A01CFNU

      Disengage the 3 clips and remove the center pillar upper end weatherstrip.

  40. REMOVE POWER SLIDE DOOR TOUCH SENSOR ASSEMBLY (w/ Power Slide Door)


    1. A01CC9L

      Disengage the clamp.

    2. Disengage the 3 clips and claw, and remove the power slide door touch sensor assembly.

  41. REMOVE SLIDE DOOR NO. 3 WEATHERSTRIP


    1. A01CG3F

      Using a clip remover, disengage the 8 clips and remove the slide door No. 3 weatherstrip.

  42. REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY


    1. A01CECT

      Disengage the clamp.

    2. Remove the 2 bolts and slide door full open stop lock assembly.

  43. REMOVE CENTER DOOR REAR WEATHERSTRIP


    1. A01CCLJ

      Using a clip remover, disengage the 9 clips and remove the center door rear weatherstrip.

  44. REMOVE SLIDE DOOR UPPER CUSHION


    1. A01CEAS

      Disengage the claw and remove the slide door upper cushion.

  45. REMOVE SLIDE DOOR LOWER CUSHION


    1. A01CBEC

      Disengage the claw and remove the slide door lower cushion.

  46. REMOVE SLIDE DOOR MUDGUARD SUB-ASSEMBLY (for Standard)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  47. REMOVE NO. 1 SIDE MUDGUARD BRACKET (for Standard)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  48. REMOVE SLIDE DOOR MUDGUARD SUB-ASSEMBLY (for Sport Package)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  49. REMOVE NO. 1 SIDE MUDGUARD BRACKET (for Sport Package)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  50. REMOVE SLIDE DOOR UPPER RAIL CUSHION


    1. A01CC98

      Disengage the clip and remove the slide door upper rail cushion.

  51. REMOVE SLIDE DOOR LOWER RAIL PLATE


    1. A01CD9U

      Remove the bolt and slide door lower rail plate.

  52. REMOVE SLIDE DOOR (w/o Power Slide Door)


    1. A01CBJ4

      Remove the 3 bolts and disconnect the slide door center hinge assembly.

      Note


      • To prevent damage, when removing the slide door, make sure that there are enough people available to hold it securely.

      • Hold the lower part of the slide door because it will become unstable after the slide door center hinge assembly is disconnected.

    2. A01CE3K

      Remove the slide door upper roller assembly as shown in the illustration.

    3. A01CF6DE01

      Turn the roller of the slide door lower roller assembly as shown in the illustration to remove it through the cutout of the slide door lower rail.

  53. REMOVE SLIDE DOOR (w/ Power Slide Door)

    SST
    09812-00010

    1. A01CGBO

      Move the slide door so that the 2 bolts can be seen.

    2. A01CDO6

      Remove the 2 bolts and disconnect the slide door lower roller assembly.

    3. A01CBJ4

      Remove the 3 bolts and disconnect the slide door center hinge assembly.

      Note


      • To prevent damage, when removing the slide door, make sure that there are enough people available to hold it securely.

      • Hold the lower part of the slide door because it will become unstable after the slide door center hinge assembly is disconnected.

    4. A01CE3K

      Remove the slide door upper roller assembly as shown in the illustration.

    5. A01CF6DE01

      Turn the roller of the slide door lower roller assembly as shown in the illustration to remove it through the cutout of the slide door lower rail.

  54. REMOVE SLIDE DOOR CENTER HINGE ASSEMBLY


    1. Move the slide door center hinge assembly to the front of the slide rail.

    2. A01CFNC

      Remove the slide door center hinge assembly as shown in the illustration.

  55. REMOVE SLIDE DOOR UPPER ROLLER ASSEMBLY


    1. A01CC2R

      Remove the 2 bolts and slide door upper roller assembly.

  56. REMOVE SLIDE DOOR LOWER ROLLER ASSEMBLY


    1. A01CAIY

      Remove the 3 bolts and slide door lower roller assembly.